1-1624094-5 TE Connectivity, 1-1624094-5 Datasheet - Page 2

• Manufacturer Part Number: 1-1624094-5
• Description: 3613C 3.3UH 10%
• Manufacturer: TE Connectivity
• Series: 3613C, Sigma Inductorsr
• Type: Ferrite Corer

Specifications of 1-1624094-5

• Inductance: 3.3µH
• Current: 355mA
• Current - Saturation: -
• Current - Temperature Rise: -
• Tolerance: ±10%
• Shielding: Unshielded
• Dc Resistance (dcr): 800 mOhm Max
• Q @ Freq: 50 @ 7.96MHz
• Frequency - Self Resonant: 45MHz
• Package / Case: 1812 (4532 Metric)
• Mounting Type: Surface Mount
• Operating Temperature: -30°C ~ 100°C
• Frequency - Test: 7.96MHz
• Material - Core: Ferrite
• Applications: General Purpose
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Test Methods
Literature No. 1773143
Issued: 01-07
Item
DC Superposition
Characteristics
Temperature
Rise
Temperature
Rise
Overcurrent
Test
Insulation
Resistance
Tensile
Strength Test
Stress Test
Drop Test
Vibration Test
Humidity Resistance
Load Test
Low Temperature
Resistance Test
Temperature
Cycle Test
High Temperature
Resistance Load Test
Dimensions are shown for
reference purposes only.
Test Notes
Dimensions
Standard
∆L/L Within -10%
Within 20°C
∆L/L Within ± 5%
No smoke and no fire
Not less than 1000 M
No separation from substrate
No breakage
No pronounced abnormality in
appearance
∆L/L Within ± 10%
Q Not less than 30
∆L/L Within ± 10%
Q Not less than 30
∆L/L Within ± 10%
Q Not less than 30
∆L/L Within ± 10%
Q Not less than 30
∆L/L Within ± 10%
Q Not less than 30
Moulded Chip Inductor 18:12
Type 3613C Series
How to Order
The measuring method for the test data given overpage are as follows:
Inductance: Direct reading from Q-meter (equivalent to YHP 4342A, jig used)
Q: Direct reading from Q-meter (equivalent to YHP 4342A, jig used)
Self resonant frequency: Grid Dipo Meter (equivalent to Measurement M159)
DC resistance: Wheatstone bridge (equivalent to YEW 2755)
Unless otherwise specified, the temperature is 20°C ± 5°C and the humidity is 65% ± 20%
Common Part
3613C - 18:12
Dimensions are in millimetres
unless otherwise specified.
3613C
Inductor
Test Method
When the allowable current was applied, the inductance was measured
with a YHP 4262A and compared with the initial value.
When the allowable current was applied, the amount of temperature rise
was measured by the change in resistance.
Measurements were taken in a temperature range of -25°C to 85°C and
the value at +20°C was used as the standard value.
Twice the allowable current was applied for a period of five minutes.
0.3mm diameter copper wires were wound around the coils three times and
measurements were taken after 250VDC was applied between the wire and the
terminals for a period of 1 minute.
After the inductors were soldered to substrates, a force of 1.0kg was applied in both
the x and y directions for a period of 5 seconds.
After the inductors were mounted on substrates, 1-mins. 10-55-10 cycle per seconds
sweeps 1.5mm stroke vibrations were applied for 2 hrs. each in the X, Y and Z directions.
The inductors were dropped 10 times from a height of 1.0 metre onto a concrete floor.
After the inductors were mounted on substrates, 1-mins. 10-55-10 cycle per seconds
sweeps 1.5mm stroke vibrations were applied for 2 hours each in the X, Y and Z
directions
Measurements were taken after the allowable current was applied while the inductors
were stored at 60°C ± 2°C in 90 to 95% RH for a period of 500 hours.
Measurements were taken after the inductors were stored at -40°C ± 2°C for period
1000 hours
Measurements were taken after the inductors were stored for 30 minutes, during which
they were subjected to 20 temperature cycles of between -25°C and +85°C.
Measurements were taken after the allowable was applied while the inductors were stored
at 85°C for a period of 1000 hours.
Inductance
Value Code
(see table)
Specifications subject to
change.
1R5
Tolerance
K - ±10%
M - 20%
J - ±5%
www.tycoelectronics.com
passives.tycoelectronics.com
K