MAX379CPE+ Maxim Integrated Products, MAX379CPE+ Datasheet
MAX379CPE+
Specifications of MAX379CPE+
Related parts for MAX379CPE+
MAX379CPE+ Summary of contents
Page 1
... OUT 8 9 DIP Pin Configurations continued at end of data sheet. ________________________________________________________________ Maxim Integrated Products Call toll free 1-800-998-8800 for free samples or literature. High-Voltage, Fault-Protected Analog Multiplexers ____________________________Features Fault Input Voltage ±75V with Power Supplies Off Fault Input Voltage ±60V with ±15V Power Supplies ...
Page 2
High-Voltage, Fault-Protected Analog Multiplexers ABSOLUTE MAXIMUM RATINGS Voltage between Supply Pins ..............................................+44V V+ to Ground ...................................................................+22V V- to Ground......................................................................-22V Digital Input Overvoltage: { V+......................................................................+ ........................................................................-4V Analog Input with Multiplexer Power On..............................±65V { } Recommended ...
Page 3
ELECTRICAL CHARACTERISTICS (continued) (V+ = +15V -15V; V (Logic Level High) = +2.4V PARAMETER SYMBOL DYNAMIC Access Time t A Break-Before-Make Delay OFF (Figure 2) Enable Delay (ON) t ON(EN) Enable Delay (OFF) ...
Page 4
High-Voltage, Fault-Protected Analog Multiplexers __________________________________________Typical Operating Characteristics INPUT LEAKAGE vs. INPUT VOLTAGE WITH 100 10 1 OPERATING RANGE 100n 10n 1n 100p 10p -100 - 100 V (V) IN NOTE: Typical R ...
Page 5
MAX358 3.0V AH ADDRESS DRIVE ( OUTPUT 50% 50% t OPEN Figure 2. Break-Before-Make Delay (t ) OPEN MAX378 3.0V AH ENABLE DRIVE 50% 0V 90% OUTPUT 90% t ON(EN) t OFF(EN) Figure ...
Page 6
High-Voltage, Fault-Protected Analog Multiplexers Truth Table—MAX378 ...
Page 7
Input switching, however, must be done with a fault- protected MAX378 multiplexer, to provide the level of protection and isolation required with most data acqui- sition inputs. Since external signal sources may contin supply voltage when the multiplexer ...
Page 8
High-Voltage, Fault-Protected Analog Multiplexers to-source voltage. The P-channel device (Q2), howev- er, has +60V V and is turned off, thereby preventing GS the input signal from reaching the output. If the input voltage is +60V, Q1 has a negative V ...
Page 9
Table 1b. MAX379 Charge Injection Injected Charge Supply Analog Voltage Input Level Out A Out B +1.7V +105pC +107pC ±5V 0V +73pC +74pC -1.7V +48pC +50pC +5V +215pC +220pC ±10V 0V +135pC +139pC -5V +62pC +63pC +10V +525pC +530pC ±15V ...
Page 10
High-Voltage, Fault-Protected Analog Multiplexers _____________________________________________Pin Configurations (continued N. N. MAX378 IN1 6 19 IN2 7 18 IN3 8 17 IN4 N.C. 14 ...
Page 11
Information (continued) PART TEMP. RANGE PIN-PACKAGE MAX379CPE 0°C to +70°C 16 Plastic DIP MAX379CWG 0°C to +70°C 24 Wide SO MAX379CJE 0°C to +70°C 16 CERDIP MAX379C/D 0°C to +70°C Dice** MAX379EPE -40°C to +85°C 16 Plastic DIP MAX379EWG ...
Page 12
... Maxim reserves the right to change the circuitry and specifications without notice at any time. implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 12 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600 12 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600 © ...