FTP-621DCL012 Fujitsu Components, FTP-621DCL012 Datasheet

no-image

FTP-621DCL012

Manufacturer Part Number
FTP-621DCL012
Description
Manufacturer
Fujitsu Components
Datasheet
1.FTP-621DCL012.pdf (9 pages)

Specifications of FTP-621DCL012

Lead Free Status / Rohs Status
Supplier Unconfirmed
24V DRIVE INTERFACE BOARD
FTP-621DCL002/012
FOR FTP-621/631/641MCL101/102/301/302
1. Centronics standard
(1) Connector (CN10)
(2) Connector pin assignment
Notes:
Connector part number
Mating connector part number : FCN-607B030-G/B (Fujitsu Components) or equivalent
No.
• Symbol “— —” means a negative logic signal.
• “–RET” signal is a return signal of the twisted pair cable.
• “I” or “O” means a signal direction from the interface board side.
INTERFACE
11
13
15
17
19
21
23
25
27
29
1
3
5
7
9
PRSTB
PRDT0
PRDT1
PRDT2
PRDT3
PRDT4
PRDT5
PRDT6
PRDT7
ACKNLG
BUSY
RINF2
SLCTIN
RINF1
ATF
Signal
I/O
O
O
O
O
I
I
I
I
I
I
I
I
I
I
I
Data strobe
Data 0
Data 1
Data 2
Data 3
Data 4
Data 5
Data 6
Data 7
Data input acknowledge
Busy
Printer status
Printer select
Printer status
Paper feed request
: FCN-605Q030-G/M (Fujitsu Components) or equivalent
Contents
No.
10
12
14
16
18
20
22
24
26
28
30
2
4
6
8
PRSTB-RET
PRDT0-RET
PRDT1-RET
PRDT2-RET
PRDT3-RET
PRDT4-RET
PRDT5-RET
PRDT6-RET
PRDT7-RET
ACKNLG-RET
BUSY-RET
INPRM-RET
INPRM
RINF3
GND
Signal
I/O
—
—
—
—
—
—
—
—
—
—
—
—
—
O
I
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Connected to logic GND
Reset
Printer status
Logic GND
Contents
1

FTP-621DCL012 Summary of contents

Page 1

... DRIVE INTERFACE BOARD FTP-621DCL002/012 FOR FTP-621/631/641MCL101/102/301/302 INTERFACE 1. Centronics standard (1) Connector (CN10) Connector part number : FCN-605Q030-G/M (Fujitsu Components) or equivalent Mating connector part number : FCN-607B030-G/B (Fujitsu Components) or equivalent (2) Connector pin assignment No. Signal I/O 1 PRSTB I Data strobe 3 PRDT0 I Data 0 5 PRDT1 I Data 1 7 PRDT2 ...

Page 2

... Connector pin number Fujitsu Components) FCN-605Q030-G/M ( equivalent No.1 No.30 No.2 FTP-621DCL002/012 (4) Data input signal timing or PRDT0 7 t1 PRSTB BUSY ACKNLG Data set time : t1 0.5 sec PRSTB pulse : t2 0.5 sec Data hold time : t3 0.5 sec PRSTB to BUSY = “H” 0.5 sec . ACKNLG pulse : t5=5 ...

Page 3

... AB22 O External address bus 22 39 RAM2 O Common RAM access Notes: • Symbol “— —” means a negative logic signal. • “I” or “O” means a signal direction from the interface board side. FTP-621DCL002/012 No. Signal I/O Contents 2 BRD — Data read 4 READY — ...

Page 4

... Power supply for head/motor (+24V — Power supply for head/motor (+24V GND — Head/motor ground 7 GND — Head/motor ground FTP-621DCL002/012 P.C.B side Cable side No. Signal I/O Contents 2 GND — Logic ground 4 V — Power supply for head/motor (+24V) DD P.C.B side Cable side No ...

Page 5

... Mating connector part number : XHP-5 (J.S.T) or equivalent No. Signal I/O Contents 1 V — Power supply for logic (+5V GND — Logic ground 5 HUP — Head-up detection FTP-621DCL002/012 No. Signal I/O Contents 2 GND — Head ground 4 GND — Head ground 6 GND — Head ground 8 HD ...

Page 6

... Note: This signal detects abnormal head temperature. 8. Connector for cutter drive (CN6)* Part number: B4B-EH (J.S.T) or equivalent No. Signal I/O Contents 1 SW1 I Cutter position detection Motor drive (+) *1 Only for FTP-621DCL012 FTP-621DCL002/012 Cable side No. Signal I/O 2 NES I Paper near end detection Cable side No. Signal I/O 2 N.C. — ...

Page 7

... Character set copy Bit image print set in high speed International character set Printer reset Line feed length set after mark detection ESC w+n Mark detection FTP-621DCL002/012 Command LF Prints buffer data and returns the line to left end of next line. FF Prints buffer data and returns the line to left end of next form ...

Page 8

... Double height print set and reset Detecting function set TOF mark detection Printing quality set Cutting* 1 Cutting type select Only for FTP-621DCL012 FTP-621DCL002/012 Command ESC J+n Sets the paper feed in normal direction. (Feeding range 255 dot lines) ESC j+n Sets the paper feed in reverse direction. ...

Page 9

... Rev. 09/2001 FTP-621DCL002/012 Part number Cable length FTP-441Y001 150 mm FTP-441Y201 500 mm FTP-621Y203 500 mm FTP-441Y401 300 mm FTP-441Y601 300 mm FTP-621Y204 300 mm FTP-621Y401 300 mm Part number FTP-040HF FTP-040HS Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info ...