SNAP-HD-BF1 OPTO 22, SNAP-HD-BF1 Datasheet
![no-image](/images/manufacturer_photos/0/4/498/opto_22_sml.jpg)
SNAP-HD-BF1
Specifications of SNAP-HD-BF1
Related parts for SNAP-HD-BF1
SNAP-HD-BF1 Summary of contents
Page 1
... SNAP module. All HDD modules work with the SNAP PAC System, which consists of SNAP PAC controllers and brains, SNAP PAC racks, SNAP I/O modules, and PAC Project software. These modules can also be used in intelligent remote I/O for ® ...
Page 2
... These cables and breakout boards are available separately and are detailed in form 1756, the SNAP TEX Cables and Breakout Boards Data Sheet, available on our website. SNAP breakout boards for high-density digital modules ...
Page 3
... SNK module NAP mounting rack NOTE: This cable does not work with SNAP-ODC-32-SRC modules. NOTE: For the SNAP-IDC-32N module, you must use 15 volt or 24 volt modules. The 5 volt modules will not work. Comparing SNAP Digital Modules IMPORTANT: SNAP high-density digital modules differ from ...
Page 4
... Firmware 8.0 and lower, no. 1 Actual turn-on and turn-off times equal the polling time plus the module time. 2 Polling time varies based on the SNAP I/O processor (brain or on-the-rack controller), processor configuration, and Ethernet host communication activity. 3 The high-density digital module uses a 16-bit counter, but the processor used with the module accumulates counts to 32 bits by periodically getting and clearing the module’ ...
Page 5
... Lifetime 1 Affects turn-on and turn-off determination 2 Time varies based on the SNAP PAC I/O processor (brain or on-the-rack controller), processor configuration, and Ethernet host communication activity. SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com © ...
Page 6
... DFARS Warranty Lifetime 1 Affects turn-on and turn-off determination 2 Time varies based on the SNAP PAC I/O processor (brain or on-the-rack controller), processor configuration, and Ethernet host communication activity. PAGE Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com 6 © ...
Page 7
... Lifetime 1 Affects turn-on and turn-off determination 2 Time varies based on the SNAP PAC I/O processor (brain or on-the-rack controller), processor configuration, and Ethernet host communication activity. SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com © ...
Page 8
... LOA LOA + 12–24 VDC Nominal NOTE: The SNAP-ODC-32-SRC and SNAP-ODC-32-SNK modules (includes -FM models) have built-in transient suppression for each channel. Additional commutating diodes are not necessary. PAGE Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com 8 © ...
Page 9
... SNAP High-Density Digital I/O Modules Pinouts and Wiring (continued) Pinouts for SNAP-IDC-32, SNAP-IDC-32-FM, and SNAP-IDC-32N Digital Modules IMPORTANT: SNAP-IDC-32 modules are polarity specific and must be wired as shown. Polarity for Polarity for SNAP-IDC-32N SNAP-IDC-32 SNAP-IDC-32-FM 10–32 VDC + 10–32 VDC + 10–32 VDC + 10–32 VDC + SALES 800-321-6786 • ...
Page 10
... DCOM DCOM To build your own SNAP-HD-BF6 header cable for use with either breakout rack, you will need the parts listed below. Both ends of the cable use the same connectors. Connector: Molex 15-04-5401 Pin housing: Molex 50-57-9320 Pins: Molex p/n 16-02-0103 Cable: Alpha 5020C or Manhattan M38910 (24 AWG, 10 ...
Page 11
... Pinouts and Wiring (continued) Pinouts—16-Channel Digital Input Modules Applies to the SNAP-IDC-16, SNAP-IDC-HT-16, SNAP-IAC-16, SNAP-IAC-A-16, and SNAP-IAC-K-16. SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com © 2006–2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. ...
Page 12
... OptoTerminal. Top View of Module Building Your Own Wiring Harness for a 16-channel Module To build your own wiring harness similar to the SNAP-HD- ACF6, you will need the following parts: Connector: Molex 39-01-2165 Pins: Molex 39-00-0214 Cable: Belden 8308 (22 AWG, 16 conductor, shielded) or ...
Page 13
... SNAP High-Density Digital I/O Modules Dimensional Drawings SNAP 32-Point Digital Modules SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com © 2006–2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. ...
Page 14
... SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com 14 © 2006–2011 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP High-Density Digital I/O Modules ...
Page 15
... SNAP High-Density Digital I/O Modules Dimensional Drawings (continued) SNAP High-Density Digital Modules (All) IMPORTANT: The mounting rack connector has 24 pins; the module connector has 20 pins. The extra pins on the mounting rack connector prevent misalignment of the module during installation. SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com © ...
Page 16
... SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com 16 © 2006–2011 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP High-Density Digital I/O Modules ...
Page 17
... SNAP I/O I/O provides the local connection to sensors and equipment. Opto 22 SNAP I/O offers points of reliable I/O per module, depending on the type of module and your needs. Analog, digital, serial, and special-purpose modules are all mixed on the same mounting rack and controlled by the same processor (SNAP PAC brain or rack-mounted controller) ...