LB25RKW01-5C24-JC-RO NKK Switches, LB25RKW01-5C24-JC-RO Datasheet - Page 11

• Manufacturer Part Number: LB25RKW01-5C24-JC-RO
• Description: Pushbutton Switches ON(ON) RECT BLK 24V RED LED CLR/RED CAP
• Manufacturer: NKK Switches
• Type: Momentary Contactr
• Series: LBr

Specifications of LB25RKW01-5C24-JC-RO

• Pole Throw Configuration: DPDT
• Switch Configuration: ON ON
• Actuator Style: Rectangular Button
• Current Rating (max): 3A
• Illumination Type: Led
• Ac Voltage Rating (max): 250VVAC
• Dc Voltage Rating (max): 30VVDC
• Contact Material: Silver Alloy
• Contact Plating: Silver
• Housing Material: Liquid Crystal Polymer/(Glass Fiber/Polyamide)
• Mechanical Life: 1000000
• Product Height (mm): 35mm
• Product Length (mm): 24mm
• Operating Temp Range: -25C to 50C
• Mounting Style: Panel
• Terminal Type: Quick Connect/Solder Lug
• Contact Form: DPDT
• Switch Function: ON - (ON)
• Illumination: Illuminated
• Illumination Color: Red
• Voltage Rating Ac: 250 Volts
• Termination Style: Solder Lug
• Actuator: Rectangular
• Flammability Rating: UL 94 V-0
• Body Length: 22.5 mm
• Body Shape: Rectangular
• Contact Rating: 3 Amps at 125 Volts, 250 Volts
• Dielectric Strength: 1000 Volts
• Insulation Resistance: 200 MOhms
• Led Size: T-1 Bi-pin
• Mounting Angle: Vertical
• Operating Force: 4.41 N
• Supply Voltage: 125 Volts, 250 Volts
• Lead Free Status / Rohs Status: Compliant

NKK Switches • email: [e-mail] • Phone [phone] • Fax [phone] • www.nkkswitches.com
Align projections on lamp with
grooves (B) in holder when
inserting lamp. To correctly join
the lamp holder and cap base,
match the cut corners (A).
Incandescent & Neon Lamps
Match projection (C) on cap
assembly with groove (C)
inside switch. Lamp terminals
will then be aligned correctly
with lamp socket.
Snap-in clip holds all switches firmly
in place.
To mount round
switch, match
the antirotation
projection on
switch with
guide cut in
panel. Snap
into panel
cutout.
AT607 & AT607N
C
Square
Snap-in Mount
C
Projection
Panel
B
B
A
For panel seal models,
Bright LED must first be
inserted into the lamp
socket which is built into
the switch. The cap can
then be placed on the
switch.
Panel Seal Models
Match clip on cap assembly with receptacle inside
switch. Lamp terminals will then be aligned correctly
with lamp socket.
ASSEMBLY INSTRUCTIONS
Insert switch from the
front of the panel with
the o-ring between the
built-in bezel and the
panel. Install mounting
nut AT075 (supplied with
switch) from the rear of
the panel.
Overtightening mounting
nut may damage the
switch housing.
Lamp Installation & LED Orientation
Installation & Maintenance
Bushing Mount
Bright LED AT627
Switch & Cap Assembly
Panel Seal
Round & Rectangular
Standard Size Pushbuttons
For snap-in models,
Bright LED must be
inserted into the cap
first. Align cut corners
Snap-in Models
C
(C) when
inserting
the LED.
O-ring
Mounting Nut
Bezel
LED
Panel
Cap Extractor
With Lamps AT607, AT607N, and
LEDs AT614, AT625, AT631, AT632:
Match projection on cap assembly with
notch inside switch. Lamp terminals
will then be aligned correctly with lamp
socket.
Align D-flat on LED with flat (B) in
holder when inserting the LED.
To correctly join the lamp holder and
cap base, match the cut corners (A).
AT109
Projection
Actuator must be in UP position.
Pull off cap with cap extractor
AT109.
Replace lamp and reassemble as
shown above.
Notch
Bright & Super Bright LEDs
AT625, AT631, AT632,
Cut Corner
Panel Seal
Lamp Replacement
Series LB
AT635
LED
Sensitive Devices
Socket Wrench
D Flat
Attention
Rubber Seal
Electrostatic
A
AT112
Projection
03-07
B