LM6584MT National Semiconductor, LM6584MT Datasheet - Page 4

• Manufacturer Part Number: LM6584MT
• Manufacturer: National Semiconductor
• Type: General Purpose Amplifierr

Specifications of LM6584MT

• Rail/rail I/o Type: Rail to Rail Input/Output
• Number Of Elements: 4
• Unity Gain Bandwidth Product: 15.3MHz
• Slew Rate: 11V/us
• Common Mode Rejection Ratio: 72dB
• Input Offset Voltage: 4mV
• Input Bias Current: 1uA
• Single Supply Voltage (typ): 9/12V
• Dual Supply Voltage (typ): Not RequiredV
• Voltage Gain In Db: 106dB
• Power Supply Rejection Ratio: 75dB
• Power Supply Requirement: Single
• Shut Down Feature: No
• Single Supply Voltage (min): 5V
• Single Supply Voltage (max): 13V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Technology: Bipolar
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 14
• Package Type: TSSOP
• Lead Free Status / Rohs Status: Not Compliant

www.national.com
SR
Φ
t
t
HD2
HD3
e
s
p
Symbol
n
m
5V AC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for at T
perature extremes.
Note 1: Note 1: Absolute maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the
device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical
Characteristics.
Note 2: For testing purposes, ESD was applied using human body model, 1.5kΩ in series with 100pF.
Note 3: Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the
maximum allowed junction temperature of 150˚C
Note 4: The maximum power dissipation is a function of T
P
Note 5: Typical values represent the most likely parametric norm.
Note 6: All limits are guaranteed by testing or statistical analysis.
Note 7: Large signal voltage gain is the total output swing divided by the input signal required to produce that swing.
Note 8: The open loop output current is guaranteed, by the measurement of the open loop output voltage swing.
Note 9: Slew Rate is the average of the raising and falling slew rates.
Note 10: Harmonics are measured with A
Note 11: Continuous operation at these output currents will exceed the power dissipation ability of the device
Note 12: Power dissipation limits may be exceeded if all four amplifiers source or sink 75mA. Voltage across the output transistors and their output currents must
be taken into account to determine the power dissipation of the device
Note 13: Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating
of the device such that T
See applications section for information on temperature de-rating of this device.
Connection Diagram
Ordering Information
14-Pin TSSOP
D
14-Pin SOIC
= (T
Package
J(MAX)
Slew Rate (Note 9)
Unity Gain Bandwidth Product
−3dB Frequency
Phase Margin
Settling Time (0.1%)
Propagation Delay
2
F
3rd Harmonic Distortion
F
Input-Referred Voltage Noise
nd
IN
IN
- T
A
Harmonic Distortion
= 1MHz (Note 10)
= 1MHz (Note 10)
)/ θ
JA
J
. All numbers apply for packages soldered directly onto a PC board.
Parameter
= T
A
Part Number
. No guarantee of parametric performance is indicated in the electrical tables under conditions of internal self heating where T
LM6584MAX
LM6584MTX
LM6584MA
LM6584MT
V
= +2 and R
A
A
A
A
V
V
f = 10kHz
L
V
V
V
V
OUT
OUT
= 100Ω and V
Package Marking
= +1, V
= +1
= −1, V
= −2, V
J(MAX)
LM6584MA
LM6584MT
= 2V
= 2V
14-Pin SOIC/TSSOP
, θ
IN
O
IN
PP
PP
(Note 13)
Conditions
JA
J
=
IN
= 3.5V
=
, and T
= 25˚C, V
= 1V
Top View
±
±
1V, R
1V, R
PP
4
PP
A
to give V
. The maximum allowable power dissipation at any ambient temperature is
L
L
= 500Ω
CM
= 500Ω
=
OUT
20059202
1
2.5k Units Tape and Reel
2.5k Units Tape and Reel
⁄
2
= 2V
V
S
Transport Media
and R
PP
95 Units/Rail
95 Units/Rail
.
(Note 6)
L
Min
= 2kΩ. Boldface limits apply at the tem-
(Note 5)
15.3
Typ
270
−53
−40
11
24
56
21
23
(Note 6)
Max
NSC Drawing
MTC14
M14A
nV/
Units
J
V/µs
MHz
MHz
deg
dBc
dBc
ns
ns
>
T
A
.