SI1413EDH-T1 Vishay, SI1413EDH-T1 Datasheet - Page 7
![](/photos/31/33/313395/516-sot-363_sml.jpg)
SI1413EDH-T1
Manufacturer Part Number
SI1413EDH-T1
Description
Manufacturer
Vishay
Type
Power MOSFETr
Datasheet
1.SI1413EDH-T1.pdf
(11 pages)
Specifications of SI1413EDH-T1
Number Of Elements
1
Polarity
P
Channel Mode
Enhancement
Drain-source On-res
0.115Ohm
Drain-source On-volt
20V
Gate-source Voltage (max)
±12V
Continuous Drain Current
2.3A
Power Dissipation
1W
Operating Temp Range
-55C to 150C
Operating Temperature Classification
Military
Mounting
Surface Mount
Pin Count
6
Package Type
SC-70
Lead Free Status / Rohs Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SI1413EDH-T1-E3
Manufacturer:
VISHAY
Quantity:
32 923
Part Number:
SI1413EDH-T1-E3
Manufacturer:
VISHAY/威世
Quantity:
20 000
INTRODUCTION
The new single 6-pin SC-70 package with a copper leadframe
enables improved on-resistance values and enhanced
thermal performance as compared to the existing 3-pin and
6-pin packages with Alloy 42 leadframes. These devices are
intended for small to medium load applications where a
miniaturized package is required. Devices in this package
come in a range of on-resistance values, in n-channel and
p-channel versions. This technical note discusses pin-outs,
package outlines, pad patterns, evaluation board layout, and
thermal performance for the single-channel version.
BASIC PAD PATTERNS
See Application Note 826, Recommended Minimum Pad
Patterns With Outline Drawing Access for Vishay Siliconix
MOSFETs, (http://www.vishay.com/doc?72286) for the basic
pad layout and dimensions. These pad patterns are sufficient
for the low to medium power applications for which this
package is intended. Increasing the drain pad pattern yields a
reduction in thermal resistance and is a preferred footprint.
The availability of four drain leads rather than the traditional
single drain lead allows a better thermal path from the package
to the PCB and external environment.
PIN-OUT
Figure 1 shows the pin-out description and Pin 1
identification.The pin-out of this device allows the use of four
pins as drain leads, which helps to reduce on-resistance and
junction-to-ambient thermal resistance.
For package dimensions see outline drawing SC-70 (6-Leads)
(http://www.vishay.com/doc?71154)
Document Number: 71334
12-Dec-03
Recommended Pad Pattern and Thermal Performance
Single-Channel LITTLE FOOTR SC-70 6-Pin MOSFET
G
D
D
1
2
3
SC-70 (6-LEADS)
FIGURE 1.
SOT-363
Top View
Copper Leadframe Version
6
5
4
D
D
S
EVALUATION BOARDS
The evaluation board (EVB) measures 0.6 inches by
0.5 inches. The copper pad traces are the same as in Figure 2.
The board allows examination from the outer pins to 6-pin DIP
connections, permitting test sockets to be used in evaluation
testing. See Figure 3.
The thermal performance of the single 6-pin SC-70 has been
measured on the EVB, comparing both the copper and
Alloy 42 leadframes. This test was first conducted on the
traditional Alloy 42 leadframe and was then repeated using the
1-inch
96 (mil)
2
PCB with dual-side copper coating.
71 (mil)
13 (mil)
FIGURE 2.
18 (mil)
0, 0 (mil)
6
1
52 (mil)
26 (mil)
SC-70 (6 leads) Single
Vishay Siliconix
SINGLE SC70-6
5
2
16 (mil)
4
3
www.vishay.com
AN815
26 (mil)
1