AM29DL164DT-120WCI Spansion Inc., AM29DL164DT-120WCI Datasheet - Page 12

• Manufacturer Part Number: AM29DL164DT-120WCI
• Manufacturer: Spansion Inc.

Specifications of AM29DL164DT-120WCI

• Cell Type: NOR
• Density: 16Mb
• Access Time (max): 120ns
• Interface Type: Parallel
• Boot Type: Top
• Address Bus: 21/20Bit
• Operating Supply Voltage (typ): 3/3.3V
• Operating Temp Range: -40C to 85C
• Package Type: FBGA
• Program/erase Volt (typ): 8.5 to 9.5V
• Sync/async: Asynchronous
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.6V
• Word Size: 8/16Bit
• Number Of Words: 2M/1M
• Supply Current: 16mA
• Mounting: Surface Mount
• Pin Count: 48
• Lead Free Status / Rohs Status: Not Compliant

DEVICE BUS OPERATIONS
This section describes the requirements and use of
the device bus operations, which are initiated through
the internal command register. The command register
itself does not occupy any addressable memory loca-
tion. The register is a latch used to store the
commands, along with the address and data informa-
tion needed to execute the command. The contents of
Legend: L = Logic Low = V
A
Notes:
1. Addresses are A19:A0 in word mode (BYTE# = V
2. The sector protect and sector unprotect functions may also be implemented via programming equipment. See the “Sector/Sector
3. If WP#/ACC = V
Word/Byte Configuration
The BYTE# pin controls whether the device data I/O
pins operate in the byte or word configuration. If the
BYTE# pin is set at logic ‘1’, the device is in word con-
figuration, DQ0–DQ15 are active and controlled by
CE# and OE#.
If the BYTE# pin is set at logic ‘0’, the device is in byte
configuration, and only data I/O pins DQ0–DQ7 are
active and controlled by CE# and OE#. The data I/O
pins DQ8–DQ14 are tri-stated, and the DQ15 pin is
used as an input for the LSB (A-1) address function.
12
Read
Write
Standby
Output Disable
Reset
Sector Protect (Note 2)
Sector Unprotect (Note 2)
Temporary Sector Unprotect
IN
Block Protection and Unprotection” section.
protection depends on whether they were last protected or unprotected using the method described in “Sector/Sector Block
Protection and Unprotection”. If WP#/ACC = V
= Address In, D
Operation
IN
IL
, the two outermost boot sectors remain protected. If WP#/ACC = V
= Data In, D
IL
, H = Logic High = V
V
0.3 V
CE# OE# WE# RESET# WP#/ACC
CC
L
L
L
X
L
L
X
OUT
±
Table 1. Am29DL16xD Device Bus Operations
= Data Out
H
X
H
X
H
H
X
L
H
X
H
X
X
L
L
L
IH
HH,
D A T A
V
, V
0.3 V
V
V
V
CC
H
H
H
L
IH
all sectors will be unprotected.
ID
ID
ID
ID
), A19:A-1 in byte mode (BYTE# = V
±
Am29DL16xD
= 8.5–12.5 V, V
(Note 3)
(Note 3)
(Note 3)
L/H
L/H
L/H
L/H
H
S H E E T
the register serve as inputs to the internal state ma-
chine. The state machine outputs dictate the function
of the device. Table 1 lists the device bus operations,
the inputs and control levels they require, and the re-
sulting output. The following subsections describe
each of these operations in further detail.
Requirements for Reading Array Data
To read array data from the outputs, the system must
drive the CE# and OE# pins to V
control and selects the device. OE# is the output con-
trol and gates array data to the output pins. WE#
should remain at V
whether the device outputs array data in words or
bytes.
The internal state machine is set for reading array data
upon device power-up, or after a hardware reset. This
ensures that no spurious alteration of the memory
content occurs during the power transition. No com-
mand is necessary in this mode to obtain array data.
Standard microprocessor read cycles that assert valid
A1 = H, A0 = L
A1 = H, A0 = L
HH
SA, A6 = H,
Addresses
SA, A6 = L,
= 9.0 ± 0.5 V, X = Don’t Care, SA = Sector Address,
(Note 2)
A
A
A
X
X
X
IN
IN
IN
High-Z High-Z
High-Z High-Z
High-Z High-Z
DQ0–
IH
D
DQ7
D
D
D
D
IH
, the two outermost boot sector
OUT
IL
IN
IN
IN
IN
. The BYTE# pin determines
).
BYTE#
= V
D
D
D
OUT
X
X
21533E6 February 26, 2009
IN
IN
IH
IL
DQ8–DQ14 = High-Z,
DQ8–DQ15
. CE# is the power
DQ15 = A-1
BYTE#
High-Z
High-Z
High-Z
High-Z
= V
X
X
IL