AT49F4096-90RC Atmel, AT49F4096-90RC Datasheet
AT49F4096-90RC
Specifications of AT49F4096-90RC
Available stocks
Related parts for AT49F4096-90RC
AT49F4096-90RC Summary of contents
Page 1
... Typical 10,000 Write Cycles Description The AT49F4096 is a 5-volt only, 4-megabit Flash Memory organized as 256K words of 16 bits each. Manufactured with Atmel’s advanced nonvolatile CMOS technology, the device offers access times with power dissipation of just 275 mW. When deselected, the CMOS standby current is less than 300 A. ...
Page 2
... To allow for simple in-system reprogrammability, the AT49F4096 does not require high input voltages for pro- gramming. Five-volt-only commands determine the read and programming operation of the device. Reading data out of the device is similar to reading from an EPROM; it has standard CE, OE, and WE inputs to avoid bus conten- tion ...
Page 3
... DATA polling may begin at any time during the program cycle. TOGGLE BIT: In addition to DATA polling the AT49F4096 provides another method for determining the end of a pro- gram or erase cycle. During a program or erase operation, successive attempts to read data from the device will result in I/O6 toggling between one and zero ...
Page 4
... Examining the toggle bit may begin at any time during a program cycle. HARDWARE DATA PROTECTION: Hardware features protect against inadvertent programs to the AT49F4096 in the following ways: (a) V sense— (typical), the program function is inhibited; (b) V Command Definition (in Hex) 1st Bus ...
Page 5
... A17 = A17 = Condition MHz OUT -400 -100 4. AT49F4096-12 0°C - 70°C -40°C - 85°C 5V 10 Manufacturer Code ( Device Code A17 = V Manufacturer Code A17 = V Device Code IH IL Min Max 10 10 300 3 50 0.8 2.0 0.45 2.4 4.2 D OUT D IN High Z High Z ...
Page 6
... Note: 1. This parameter is characterized and is not 100% tested. AT49F4096 6 AT49F4096-90 Min after the address transition without impact on t ACC after the falling edge of CE without impact Output Test Load Max 6 12 AT49F4096-12 Max Min Max 90 120 90 120 ACC after an address change CE ...
Page 7
AC Word Load Characteristics Symbol Parameter Address, OE Set-up Time AS OES t Address Hold Time AH t Chip Select Set-up Time CS t Chip Select Hold Time CH t Write Pulse Width (WE or CE) WP ...
Page 8
... OE must be high only when WE and CE are both low. 2. For chip erase, the address should be 5555. For sector erase, the address depends on what sector erased. (See note 4 under command definitions.) 3. For chip erase, the data should be 10 AT49F4096 8 Min , and for sector erase, the data should Max ...
Page 9
Data Polling Characteristics Symbol Parameter t Data Hold Time Hold Time OEH ( Output Delay OE t Write Recovery Time WR Notes: 1. These parameters are characterized and not 100% tested. 2. See t ...
Page 10
... The device does not remain in identification mode if powered down. 4. The device returns to standard operation mode. 5. Manufacturer Code is 1FH. The Device Code is 92H. 6. Either one of the Product ID Exit commands can be used. AT49F4096 10 (1) Boot Block Lockout Feature Enable Algorithm (1) LOAD DATA F0 TO ...
Page 11
... Users requiring the boot block the higher address range should contact Atmel. 48T 48-Lead, Thin Small Outline Package (TSOP) 44R 44-Lead, 0.525" Wide, Plastic Gull Wing Small Outline Package (SOIC) Ordering Code AT49F4096-90TC AT49F4096-90RC AT49F4096-90TI AT49F4096-90RI AT49F4096-12TC AT49F4096-12RC AT49F4096-12TI AT49F4096-12RI Package Type ...
Page 12
... Packaging Information 44R, 44-Lead, 0.525" Wide, Plastic Gull Wing Small Outline (SOIC) Dimensions in Inches and (Millimeters) AT49F4096 12 48T, 48-Lead, Plastic Thin Small Outline Package (TSOP) Dimensions in Millimeters and (Inches)* JEDEC OUTLINE MO-142 DD *Controlling dimension: millimeters ...
Page 13
... No licenses to patents or other intellectual prop Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life suppor t devices or systems. ...