LP8340CLD-5.0 National Semiconductor, LP8340CLD-5.0 Datasheet - Page 7

• Manufacturer Part Number: LP8340CLD-5.0
• Manufacturer: National Semiconductor

Specifications of LP8340CLD-5.0

• Voltage Regulator Type: Linear
• Topology: LDO
• Regulator Output Type: Fixed
• Polarity Type: Positive
• Number Of Outputs: Single
• Input Voltage (min): 2.7V
• Input Voltage (max): 10V
• Output Voltage: 5V
• Package Type: LLP EP
• Output Current: 1A
• Load Regulation: 25mV
• Line Regulation: 4mV
• Output Voltage Accuracy: ±1.5%
• Operating Temp Range: 0C to 125C
• Operating Temperature Classification: Commercial
• Dropout Voltage@current (max): 0.65@800mA/0.8@1A
• Dropout Voltage@current (typ): 0.33@800mA/0.42@1A
• Pin Count: 6
• Mounting: Surface Mount
• Quiescent Current (max): 50uA
• Lead Free Status / Rohs Status: Not Compliant

T
e
Symbol
n
SD
LP8340I Electrical Characteristics
Unless otherwise specified all limits guaranteed for V
the full operating temperature range of T
Note 1: Absolute Maximum ratings indicate limits beyond which damage may occur. Electrical specifications do not apply when operating the device outside of its
rated operating conditions.
Note 2: All voltages are with respect to the potential at the ground pin.
Note 3: Maximum Power dissipation for the device is calculated using the following equations:
where T
the LLP package is specifically dependant on the PCB trace area, trace material, and the number of layers and thermal vias. For improved thermal resistance and
power dissipation for the LLP package, refer to Application Note AN-1187.
Note 4: Typical Values represent the most likely parametric norm.
Note 5: All limits are guaranteed by testing or statistical analysis.
Note 6: Human body model 1.5kΩ in series with 100pF.
Note 7: Condition does not apply to input voltages below 2.7V since this is the minimum input operating voltage.
Note 8: Dropout voltage is measured by reducing V
J(MAX)
Thermal Shutdown
Temp.
Thermal Shutdown Hyst.
ADJ Input Leakage
Current
V
Output Noise
OUT
is the maximum junction temperature, T
Leakage Current
Parameter
V
LP8340-ADJ
ADJ = OUT, V
LP8340-1.8, V
LP8340-2.5, V
LP8340-3.3, V
LP8340-5.0, V
10Hz to 10kHz, R
ADJ
J
IN
= 1.5V or 0V
= −40˚C to 125˚C
A
until V
is the ambient temperature, and θ
O
drops 100mV from its normal value.
OUT
OUT
OUT
OUT
OUT
IN
Conditions
L
= 2.5V, V
= 3.5V, V
= 4V, V
= 6V, V
= 2V, V
= 1kΩ, C
= V
(Continued)
O
+ 1V, C
IN
IN
IN
7
IN
IN
OUT
= 10V
= 10V
= 10V
= 10V
= 10V
IN
= 10µF
JA
= C
is the junction-to-ambient thermal resistance. The value of the θ
OUT
= 10µF, T
(Note 5)
Min
J
= 25˚C. Boldface limits apply over
(Note 4)
±
Typ
160
250
0.01
10
(Note 5)
±
Max
10
10
10
10
10
100
www.national.com
µVrms
Units
nA
µA
JA
˚C
for