2N1131 MICROSEMI, 2N1131 Datasheet - Page 3

• Manufacturer Part Number: 2N1131
• Manufacturer: MICROSEMI

Specifications of 2N1131

• Transistor Polarity: PNP
• Number Of Elements: 1
• Collector-emitter Voltage: 40V
• Collector-base Voltage: 50V
• Emitter-base Voltage: 5V
• Collector Current (dc) (max): 600mA
• Dc Current Gain (min): 20
• Power Dissipation: 600mW
• Operating Temp Range: -65C to 200C
• Operating Temperature Classification: Military
• Mounting: Through Hole
• Pin Count: 3
• Package Type: TO-39
• Lead Free Status / Rohs Status: Not Compliant

6 Lake Street, Lawrence, MA 01841
1-800-446-1158 / [phone] / Fax: [phone]
Website: http: //www.microsemi.com
NOTES:
T4-LDS-0187 Rev. 1 (101882)
1. Dimensions are in inches.
2. Millimeters are given for general information only.
3. Beyond r (radius) maximum, TW shall be held for a minimum length of .011 inch (0.28 mm).
4. Dimension TL measured from maximum HD.
5. Body contour optional within zone defined by HD, CD, and Q.
6. CD shall not vary more than .010 inch (0.25 mm) in zone P. This zone is controlled for automatic handling.
7. Leads at gauge plane .054 +.001, -.000 inch (1.37 +0.03, -0.00 mm) below seating plane shall be within .007 inch (0.18
8. Dimension LU applies between L
9. All three leads.
10. The collector shall be internally connected to the case.
11. Dimension r (radius) applies to both inside corners of tab.
12. In accordance with ASME Y14.5M, diameters are equivalent to φx symbology.
13. Lead 1 = emitter, lead 2 = base, lead 3 = collector.
14. * For L-suffix or non-S-suffix devices (TO-5), dimension LL = 1.5 inches (38.10 mm) min. and 1.75 inches (44.45 mm)
mm) radius of true position (TP) at maximum material condition (MMC) relative to tab at MMC. The device may be
measured by direct methods or by gauging procedure.
uncontrolled in and beyond LL minimum.
max. For non-L suffix types (TO-39), dimension LL = .5 inch (12.70 mm) min. and .750 inch (19.05 mm) max..
* FIGURE 1. Physical dimensions 2N1131 and 2N1132 ( TO-39), 2N1131L and 2N1132L (TO-5).
1
and L
2
PACKAGE DIMENSIONS
. Dimension LD applies between L
TECHNICAL DATA SHEET
Symbol
HD
TW
CD
CH
LD
LU
LC
LL
TL
L
L
Q
α
P
r
1
2
.305
.240
.335
.016
.500
.016
.250
.100
.029
.028
Min
.200 TP
45° TP
Inches
Gort Road Business Park, Ennis, Co. Clare, Ireland
Tel: [phone] Fax: [phone]
2
and LL minimum. Diameter is
Max
.335
.260
.370
.021
.750
.019
.050
.050
.045
.034
.010
Dimensions
12.70
Min
7.75
6.10
8.51
0.41
0.41
6.35
2.54
0.74
0.71
Millimeters
5.08 TP
45° TP
19.05
Max
8.51
6.60
9.40
0.53
0.48
1.27
1.27
1.14
0.86
0.25
7, 8, 12
Note
7, 8
7, 8
7, 8
7, 8
10
6
5
4
3
6
Page 3 of 3