MAX395CWG Maxim Integrated Products, MAX395CWG Datasheet - Page 6

• Manufacturer Part Number: MAX395CWG
• Description: Analog Switch ICs
• Manufacturer: Maxim Integrated Products

Specifications of MAX395CWG

• Switch Configuration: SPST
• On Resistance (max): 500 Ohms at 3.6 V
• On Time (max): 600 ns at 3.6 V
• Off Time (max): 400 ns at 5.5 V
• Supply Voltage (max): 16 V
• Supply Voltage (min): 2.7 V
• Maximum Power Dissipation: 941 mW
• Maximum Operating Temperature: + 70 C
• Package / Case: SOIC-24 Wide
• Minimum Operating Temperature: 0 C
• Switch Current (typ): 0.007 mA at 5.5 V
• Lead Free Status / Rohs Status: No

TIMING CHARACTERISTICS—Single +5V Supply (Figure 1)
(V+ = +4.5V to +5.5V, V- = 0V, T
Serially Controlled, Low-Voltage,
8-Channel SPST Switch
6
Note 1: The algebraic convention is used in this data sheet; the most negative value is shown in the minimum column.
Note 2: ∆R
Note 3: Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at room temp.
Note 4: Guaranteed by design.
Note 5: Leakage testing at single supply is guaranteed by testing with dual supplies.
Note 6: See Figure 6. Off isolation = 20log
Note 7: Between any two switches. See Figure 3.
SERIAL DIGITAL INTERFACE
SERIAL DIGITAL INTERFACE
SCLK Frequency
Cycle Time (Note 4)
CS Lead Time (Note 4)
CS Lag Time (Note 4)
SCLK High Time (Note 4)
SCLK Low Time (Note 4)
Data Setup Time (Note 4)
Data Hold Time (Note 4)
DIN Data Valid after Falling SCLK
(Note 4)
Rise Time of DOUT (Note 4)
Allowable Rise Time at DIN,
SCLK (Note 4)
Fall Time of DOUT (Note 4)
Allowable Fall Time at DIN,
SCLK (Note 4)
RESET Minimum Pulse Width
_______________________________________________________________________________________
specified voltages. Flatness is defined as the difference between the maximum and minimum value of on-resistance as
measured over the specified analog signal range.
PARAMETER
ON
= R
ON(max)
- R
ON(min)
A
= T
. On-resistance match between channels and on-resistance flatness are guaranteed only with
MIN
SYMBOL
t
CH
f
t
SCLK
t
CSH2
t
t
t
t
to T
CSS
t
t
t
t
SCR
t
t
SCF
CH
DH
DO
RW
CL
DS
DR
DF
+ t
10
CL
MAX
V
COM
, unless otherwise noted. Typical values are at T
/V
50% of SCLK to 10% of
DOUT, C
20% of V+ to 70% of V+,
C
20% of V+ to 70% of V+,
C
20% of V+ to 70% of V+,
C
20% of V+ to 70% of V+,
C
NO
L
L
L
L
= 10pF
= 10pF
= 10pF
= 10pF
, V
COM
L
= 10pF
= output. NO = input to off switch.
CONDITIONS
C, E, M
C, E, M
C, E, M
C, E, M
C, E, M
C, E, M
C, E, M
C, E, M
T
C, E, M
C, E, M
C, E, M
C, E, M
C, E, M
T
A
A
= +25°C
= +25°C
A
= +25°C.)
MIN
480
240
240
190
190
200
0
0
(Note 2)
TYP
-17
17
85
70
MAX
400
100
100
2.1
2
2
UNITS
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
µs
ns
µs
ns