ICL7631CMJE Maxim Integrated Products, ICL7631CMJE Datasheet - Page 12

• Manufacturer Part Number: ICL7631CMJE
• Description: OP Amp Triple GP ±8V/16V 16-Pin CDIP N
• Manufacturer: Maxim Integrated Products
• Type: General Purpose Amplifierr

Specifications of ICL7631CMJE

• Package: 16CDIP N
• Typical Gain Bandwidth Product: 0.044 MHz
• Number Of Channels Per Chip: 3
• Typical Input Noise Voltage Density: 100@±1V nV/rtHz
• Typical Noninverting Input Noise Current Density: 0.01@±1V pA/rtHz
• Typical Slew Rate: 0.16@±5V V/us
• Typical Voltage Gain: 90 dB
• Maximum Input Bias Current: 0.00005@±1V uA
• Power Supply Type: Single|Dual
• Minimum Dual Supply Voltage: ±1 V
• Maximum Dual Supply Voltage: ±8 V
• Typical Dual Supply Voltage: ±3|±5 V
• Minimum Single Supply Voltage: 2 V
• Maximum Single Supply Voltage: 16 V
• Typical Single Supply Voltage: 3|5|9|12|15 V
• Maximum Input Offset Voltage: 10@±1V mV
• Maximum Operating Supply Voltage: ±8|16 V
• Case: DIP-16L

Total Supply Voltage (V+ to V-) ...........................................+18V
Input Voltage ........................................(V+ + 0.3V) to (V- - 0.3V)
Differential Input Voltage (Note 5).......±|(V+ + 0.3V) - (V- - 0.3V)
Duration of Output Short Circuit (Note 6) ......................Unlimited
Continuous Power Dissipation (T
Single/Dual/Triple/Quad
Operational Amplifiers
ABSOLUTE MAXIMUM RATINGS (Triple/Quad)
ELECTRICAL CHARACTERISTICS (Triple/Quad)
(V
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Note 5: Long-term offset voltage stability will be degraded if large input differential voltages are applied for long periods of time.
Note 6: The outputs may be shorted to ground or to either supply for V SUPP ≤ 10V. Care must be taken to insure that the
12
Input Offset Voltage
Temperature
Coefficient of V
Input Offset Current
Input Bias Current
Common-Mode
Voltage Range
Output Voltage
Swing
Large-Signal Voltage
Gain
Unity-Gain
Bandwidth
Input Resistance
Common-Mode
Rejection Ratio
SUPP
TO-99 Metal Can (derate 2mW/°C above +25°C) .......250mW
8-Pin Minidip (derate 2mW/°C above +25°C) ..............250mW
14-Pin Plastic (derate 3mW/°C above +25°C) .............375mW
14-Pin CERDIP (derate 4mW/°C above +25°C)...........500mW
PARAMETER
______________________________________________________________________________________
= ±1.0V, I
dissipation rating is not exceeded.
OS
Q
= 10µA, T
SYMBOL
∆V
CMRR
V
V
A
GBW
I
V
BIAS
I
R
OS
CMR
OUT
OS
VOL
OS
IN
A
/∆T
= +25°C, unless otherwise noted.) (Specifications apply to ICL7631/7632/7642 only.)
A
= +25°C)
R
T
R
T
R
T
0°C ≤ T
T
0°C ≤ T
R
R
+70°C
V
T
V
0°C ≤ T
R
A
MIN
A
A
A
S
S
S
L
L
O
O
S
≤ 100kΩ,
= +25°C
≤ 100kΩ,
≤ 100kΩ
= +25°C
= +25°C
= 1MΩ, T
= 1MΩ, 0°C ≤ T
= +25°C
≤ 100kΩ
= ±0.1V, R
= ±0.1V, R
CONDITIONS
≤ T
A
A
A
A
≤ +70°C
≤ +70°C
≤ +70°C
≤ T
A
MAX
L
L
= +25°C
= 1MΩ,
= 1MΩ,
A
≤
MIN
-0.4
Operating Temperature Ranges:
M Series .............................................................-55°C to +125°C
E Series................................................................-40°C to +85°C
C Series .................................................................-0°C to +70°C
Storage Temperature Range ............................-55°C to +150°C
Lead Temperature (soldering, 10s) ................................+300°C
16-Pin Plastic (derate 3mW/°C above +25°C) .............375mW
16-Pin CERDIP (derate 4mW/°C above +25°C)...........500mW
ICL76XXB
±0.98
±0.96
0.044
TYP
10
0.5
1.0
15
90
80
80
12
MAX
+0.6
300
500
30
50
5
7
MIN
-0.4
ICL76XXC
±0.98
±0.96
0.044
TYP
10
0.5
1.0
20
90
80
80
12
MAX
+0.6
300
500
10
12
30
50
UNITS
µV/°C
MHz
mV
pA
pA
dB
dB
Ω
V
V