FTRJ1321P1BTL Finisar Corporation, FTRJ1321P1BTL Datasheet
FTRJ1321P1BTL
Specifications of FTRJ1321P1BTL
Related parts for FTRJ1321P1BTL
FTRJ1321P1BTL Summary of contents
Page 1
... IEEE Std 802.3 SONET OC-12 and SONET OC-3 standards via the 2-wire serial bus specified in the SFP MSA. PRODUCT SELECTION x Finisar Corporation May 11, 2005 Rev. J FTRJ1321P1xTL APPLICATIONS • SONET OC- SDH STM I-16 • SONET OC- SDH STM I-4 • SONET OC SDH STM I-1 • ...
Page 2
... LOS is open collector output. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. Towards Bezel Pinout of Connector Block on Host Board Finisar Corporation May 11, 2005 Rev. J Name/Description <0.8V. DIS VeeT ...
Page 3
... All transceiver specifications are compliant with a power supply sinusoidal modulation 1.5 MHz up to specified value applied through the power supply filtering network shown on page 23 of the Small Form-factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA), September 14, 2000. Finisar Corporation May 11, 2005 Rev. J Symbol Min ...
Page 4
... With worst-case extinction ratio. Measured with a PRBS 2 consecutive ones and 72 consecutive zeros. 5. With worst-case extinction ratio. Measured with a PRBS 2 6. With worst-case extinction ratio. Measured with a PRBS 2 Finisar Corporation May 11, 2005 Rev - ° ° ° ° 3.00 to 3.60 Volts Symbol ...
Page 5
... Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TÜV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request. Finisar Corporation May 11, 2005 Rev. J Symbol ...
Page 6
... Note AN-2030. Digital diagnostics for the FTRJ1321P1xTL are externally calibrated by default. Please note that evaluation board FDB-1018 is available with Finisar ModDEMO software that allows simple to use communication over the 2-wire serial interface. Finisar Corporation May 11, 2005 Rev very closely related to the E 2 ...
Page 7
... FTRJ1321P1xTL Pluggable SFP Product Specification - May 2005 IX. Mechanical Specifications Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA) Finisar Corporation May 11, 2005 Rev. J FTRJ1321P1BTL Page 7 ...
Page 8
... FTRJ1321P1xTL Pluggable SFP Product Specification - May 2005 Finisar Corporation May 11, 2005 Rev. J FTRJ1321P1WTL Page 8 ...
Page 9
... FTRJ1321P1xTL Pluggable SFP Product Specification - May 2005 X. PCB Layout and Bezel Recommendations Finisar Corporation May 11, 2005 Rev Page 9 ...
Page 10
... FTRJ1321P1xTL Pluggable SFP Product Specification - May 2005 Finisar Corporation May 11, 2005 Rev Page 10 ...
Page 11
... IEEE Standards Department, 2002. 4. “Fibre Channel Draft Physical Interface Specification (FC-PI 13.0)”. American National Standard for Information Systems. XII. For More Information Finisar Corporation 1308 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com Finisar Corporation May 11, 2005 Rev Page 11 ...