DS90CF384MTDX National Semiconductor, DS90CF384MTDX Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
DS90CF384MTDX
Manufacturer Part Number
DS90CF384MTDX
Description
LVDS Flat Panel Display 0.45V 56-Pin TSSOP T/R
Manufacturer
National Semiconductor
Datasheet
1.DS90CF384MTDNOPB.pdf
(20 pages)
Specifications of DS90CF384MTDX
Package
56TSSOP
Number Of Drivers
28
Transmission Data Rate
1800 Mbps
Differential Input Low Threshold Voltage
-0.1 V
Differential Input High Threshold Voltage
0.1 V
Typical Operating Supply Voltage
3.3 V
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
DS90CF384MTDX
Manufacturer:
NS/国半
Quantity:
20 000
Company:
Part Number:
DS90CF384MTDX/NOPB
Manufacturer:
MIT
Quantity:
6 228
www.national.com
AC Timing Diagrams
C — Setup and Hold Time (Internal data sampling window) defined by Rspos (receiver input strobe position) min and max
Tppos — Transmitter output pulse position (min and max)
RSKM = Cable Skew (type, length) + Source Clock Jitter (cycle to cycle) (Note 10) + ISI (Inter-symbol interference) (Note 11)
Cable Skew — typically 10 ps–40 ps per foot, media dependent
Note 10: Cycle-to-cycle jitter is less than 250 ps at 65 MHZ
Note 11: ISI is dependent on interconnect length; may be zero
Applications Information
The DS90C383 and DS90CF384 are backward compatible
with the existing 5V FPD Link transmitter/receiver pair
(DS90CR583, DS90CR584, DS90CF583 and DS90CF584).
To upgrade from a 5V to a 3.3V system the following must be
addressed:
1. Change 5V power supply to 3.3V. Provide this supply to
2. The DS90C383 (transmitter) incorporates a rise/fall
3. The DS90C383 transmitter input and control inputs ac-
the V
and receiver devices. This change may enable the re-
moval of a 5V supply from the system, and power may
be supplied from an existing 3V power source.
strobe select pin. This select function is on pin 17,
formerly a V
rise/fall strobe select pin is connected to V
configured with a rising edge strobe. In a system cur-
rently using a 5V rising edge strobe transmitter
(DS90CR583), no layout changes are required to ac-
commodate the new rise/fall select pin on the 3.3V
transmitter. The V
the device will be configured with a rising edge strobe.
cept 3.3V TTL/CMOS levels. They are not 5V tolerant.
When converting from a 5V falling edge transmitter
(DS90CF583) to the 3V transmitter a minimal board
layout change is necessary. The 3.3V transmitter will
not be configured with a falling edge strobe if V
mains connected to the select pin. To guarantee the
3.3V transmitter functions with a falling edge strobe pin
17 should be connected to ground OR left unconnected.
When not connected (left open) and internal pull-down
resistor ties pin 17 to ground, thus configuring the trans-
mitter with a falling edge strobe.
CC
, LVDS V
CC
connection on the 5V products. When the
CC
CC
and PLL V
signal may remain at pin 17, and
CC
(Continued)
of both the transmitter
FIGURE 19. Receiver LVDS Input Skew Margin
CC
, the part is
CC
re-
12
DS012887-21