MAX4052ACSE+ Maxim Integrated Products, MAX4052ACSE+ Datasheet - Page 12
![IC MULTIPLEXER DUAL 4X1 16SOIC](/photos/6/66/66630/175-16-soic_sml.jpg)
MAX4052ACSE+
Manufacturer Part Number
MAX4052ACSE+
Description
IC MULTIPLEXER DUAL 4X1 16SOIC
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX4053ACSE.pdf
(19 pages)
Specifications of MAX4052ACSE+
Function
Multiplexer
Circuit
2 x 4:1
On-state Resistance
100 Ohm
Voltage Supply Source
Single, Dual Supply
Voltage - Supply, Single/dual (±)
2 V ~ 16 V, ±2.7 V ~ 8 V
Current - Supply
1µA
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
16-SOIC (0.154", 3.90mm Width)
Product
Multiplexer
Number Of Lines (input / Output)
4.0 / 1.0
Supply Voltage (max)
16 V
Supply Voltage (min)
2 V
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Mounting Style
SMD/SMT
Number Of Input Lines
4.0
Number Of Output Lines
1.0
Power Dissipation
696 mW
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
V+ and GND power the internal logic and logic-level
translators, and set both the input and output logic lim-
its. The logic-level translators convert the logic levels
into switched V+ and V- signals to drive the gates of
the analog signals. This drive signal is the only connec-
tion between the logic supplies (and signals) and the
analog supplies. V+ and V- have ESD-protection
diodes to GND.
The logic-level thresholds are TTL/CMOS compatible
when V+ is +5V. As V+ rises, the threshold increases
slightly, so when V+ reaches +12V, the threshold is
about 3.1V; above the TTL-guaranteed high-level mini-
mum of 2.8V, but still compatible with CMOS outputs.
These devices operate with bipolar supplies between
±3.0V and ±8V. The V+ and V- supplies need not be
symmetrical, but their sum cannot exceed the absolute
maximum rating of +17V.
These devices operate from a single supply between
+3V and +16V when V- is connected to GND. All of the
bipolar precautions must be observed. At room temper-
ature, they actually “work” with a single supply at near
or below +1.7V, although as supply voltage decreases,
switch on-resistance and switching times become very
high.
Proper power-supply sequencing is recommended for
all CMOS devices. Do not exceed the absolute maxi-
mum ratings, because stresses beyond the listed rat-
ings can cause permanent damage to the devices.
Always sequence V+ on first, then V-, followed by the
logic inputs (NO) and by COM. If power-supply
sequencing is not possible, add two small signal diodes
(D1, D2) in series with the supply pins for overvoltage
protection (Figure 1).
Adding diodes reduces the analog signal range to one
diode drop below V+ and one diode drop above V-, but
does not affect the devices’ low switch resistance and
low leakage characteristics. Device operation is
unchanged, and the difference between V+ and V-
should not exceed 17V. These protection diodes are
not recommended when using a single supply if signal
levels must extend to ground.
Low-Voltage, CMOS Analog
Multiplexers/Switches
12
______________________________________________________________________________________
Overvoltage Protection
Bipolar Supplies
Single Supply
In 50Ω systems, signal response is reasonably flat up
to 50MHz (see Typical Operating Characteristics).
Above 20MHz, the on response has several minor
peaks which are highly layout dependent. The problem
is not turning the switch on, but turning it off. The off-
state switch acts like a capacitor, and passes higher
frequencies with less attenuation. At 10MHz, off isola-
tion is about -45dB in 50Ω systems, becoming worse
(approximately 20dB per decade) as frequency
increases. Higher circuit impedances also make off iso-
lation worse. Adjacent channel attenuation is about 3dB
above that of a bare IC socket, and is entirely due to
capacitive coupling.
Figure 1. Overvoltage Protection Using External Blocking
Diodes
EXTERNAL BLOCKING DIODE
EXTERNAL BLOCKING DIODE
COM
High-Frequency Performance
*
*
V+
V-
V+
V-
D1
D2
* INTERNAL PROTECTION DIODES
*
*
NO
MAX4051/A
MAX4052/A
MAX4053/A