MC34063SMDBGEVB ON Semiconductor, MC34063SMDBGEVB Datasheet - Page 3

• Manufacturer Part Number: MC34063SMDBGEVB
• Description: BOARD EVALUATION MC34063
• Manufacturer: ON Semiconductor
• Series: -r

Specifications of MC34063SMDBGEVB

• Design Resources: MC34063SMDBGEVB Schematic MC34063SMDBGEVB BOM MC34063SMDBGEVB Gerber Files
• Main Purpose: DC/DC, Step Up or Down
• Outputs And Type: 1, Non-Isolated
• Power - Output: -
• Voltage - Output: Adjustable
• Current - Output: 1.5A
• Voltage - Input: 3 ~ 40 V
• Regulator Topology: Buck-Boost
• Frequency - Switching: 100kHz
• Board Type: Fully Populated
• Utilized Ic / Part: MC34063
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: MC34063SMDBGEVBOS

4. T
5. Low duty cycle pulse techniques are used during test to maintain junction temperature as close to ambient temperature as possible.
6. If the output switch is driven into hard saturation (non−Darlington configuration) at low switch currents (≤ 300 mA) and high driver currents
* The 100 W resistor in the emitter of the driver device requires about 7.0 mA before the output switch conducts.
ELECTRICAL CHARACTERISTICS
OSCILLATOR
OUTPUT SWITCH (Note 5)
COMPARATOR
TOTAL DEVICE
Frequency (V
Charge Current (V
Discharge Current (V
Discharge to Charge Current Ratio (Pin 7 to V
Current Limit Sense Voltage (I
Saturation Voltage, Darlington Connection
Saturation Voltage (Note 6)
DC Current Gain (I
Collector Off−State Current (V
Threshold Voltage
Threshold Voltage Line Regulation (V
Input Bias Current (V
Supply Current (V
( I
V
T
(≥ 30 mA), it may take up to 2.0 ms for it to come out of saturation. This condition will shorten the off time at frequencies ≥ 30 kHz, and is
magnified at high temperatures. This condition does not occur with a Darlington configuration, since the output switch cannot saturate. If a
non−Darlington configuration is used, the following output drive condition is recommended:
Forced b of output switch :
(I
T
T
Pin 5
low
high
SW
A
A
MC33063, MC34063
MC33063V, NCV33063
SW
= 25°C
= T
= 0°C for MC34063, SC34063; − 40°C for MC33063, SC33063, MC33063V, NCV33063
= 1.0 A, Pins 1, 8 connected)
= +70°C for MC34063, SC34063; + 85°C for MC33063, SC33063; +125°C for MC33063V, NCV33063
= 1.0 A, R
> V
low
th
to T
, Pin 2 = GND, remaining pins open)
Pin 5
high
Pin 8
CC
= 0 V, C
CC
SW
in
CC
= 5.0 V to 40 V, C
= 5.0 V to 40 V, T
= 82 W to V
= 1.0 A, V
= 0 V)
= 5.0 V to 40 V, T
T
= 1.0 nF, T
I C driver – 7.0 mA *
chg
CE
Characteristics
CE
= 40 V)
= I
CC
I C output
= 5.0 V, T
dischg
, Forced b ] 20)
CC
A
T
A
= 25°C)
= 3.0 V to 40 V)
= 1.0 nF, Pin 7 = V
= 25°C)
(V
, T
A
= 25°C)
CC
A
A
CC
= 25°C)
= 25°C)
= 5.0 V, T
, T
w 10
A
= 25°C)
http://onsemi.com
A
= T
CC
low
,
to T
3
high
[Note 4], unless otherwise specified.)
I
V
dischg
Symbol
V
V
ipk(sense)
Reg
I
I
dischg
CE(sat)
CE(sat)
C(off)
f
I
h
I
V
osc
chg
I
CC
FE
IB
th
line
/I
chg
1.225
1.21
Min
140
250
5.2
24
24
50
−
−
−
−
−
−
−
0.45
0.01
1.25
−20
Typ
220
300
6.5
1.0
1.4
1.4
33
35
75
−
−
1.275
−400
Max
1.29
260
350
100
7.5
1.3
0.7
5.0
6.0
4.0
42
42
−
Unit
kHz
mV
mV
mA
nA
mA
mA
mA
V
V
V
−
−