SY58040UMG Micrel Inc, SY58040UMG Datasheet - Page 4

• Manufacturer Part Number: SY58040UMG
• Description: IC CROSSPOINT SWITCH 4X4 44MLF
• Manufacturer: Micrel Inc
• Series: SY58r

Specifications of SY58040UMG

• Function: Crosspoint Switch
• Circuit: 1 x 4:4
• Current - Supply: 225mA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 44-MLF®, QFN
• Number Of Arrays: 1
• Differential Data Transmission: Yes
• Power Supply Requirement: Single
• Mounting: Surface Mount
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Operating Temperature Classification: Industrial
• Cascading Capability: No
• Line Code: NRZ
• On-chip Buffers: No
• On-chip Decoder: No
• On-chip Latch Circuit: No
• On-chip Mux/demux: No
• Programmable: No
• Operating Supply Voltage (max): 3.6V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Input Level: CML/LVDS/LVPECL
• Output Level: CML
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 576-1397

Micrel, Inc.
Absolute Maximum Ratings
Power Supply Voltage (V
Input Voltage (V
CML Output Voltage (V
Termination Current
Input Current
V
Lead Temperature (soldering, 20 sec.) ...................... 260°C
Storage Temperature Range (T
T
Symbol
V
I
R
R
V
V
V
V
V
V
Notes:
1. Permanent device damage may occur if ratings in the “Absolute Maximum Ratings” section are exceeded. This is a stress rating only and functional
2. The data sheet limits are not guaranteed if the device is operated beyond the operating ratings.
3. Due to the limited drive capability, use for input of the same package only.
4. Package thermal resistance assumes exposed pad is soldered (or equivalent) to the device’s most negative potential on the PCB. θ
5. The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established.
6. V
M9999-103009
[e-mail] or [phone]
CC
A
CC
IH
IL
IN
DIFF_IN
T_IN
REF-AC
REF-AC
IN
DIFF_IN
= –40°C to +85°C, unless otherwise stated.
DC ELECTRICAL CHARACTERISTICS
Source or sink current on VT pin ........................ ±100mA
Source or sink current on IN, /IN .......................... ±50mA
Source or sink current on IN, /IN ............................ ±2mA
operation is not implied for conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratings
conditions for extended periods may affect device reliability.
still-air number, unless otherwise stated.
IH
(min) not lower than 1.2V.
Current
(3)
Parameter
Power Supply Voltage
Power Supply Current
Input Resistance (IN-to-V
Differential Input Resistance
(IN-to-/IN)
Input HIGH Voltage
(IN-to-/IN)
Input LOW Voltage
(IN-to-/IN)
Input Voltage Swing
(IN-to-/IN)
Differential Input Voltage Swing
|IN – /IN|
IN to V
Output Reference Voltage
IN
(3)
) ...........................................–0.5V to V
(3)
T
(IN-to-/IN)
OUT
CC
) ..........V
) .......................–0.5V to +4.0V
S
) ............ –65°C to +150°C
CC
T,
/IN-to-V
(1)
–0.5V to V
T
)
Condition
V
V
No load, max. V
Includes current from internal 50Ω pull-up
on each output.
Note 6
See Figure 1a.
See Figure 1b.
CC
CC
CC
(5)
+5.0V
= 2.5V.
= 3.3V.
CC
4
Operating Ratings
Power Supply Voltage (V
Ambient Temperature Range (T
Package Thermal Resistance
CC
MLF
MLF
.
Still-Air ............................................................. 23°C/W
Junction-to-board ............................................. 12°C/W
®
®
(θ
(ψ
JA
JB
)
)
CC
(2)
V
V
) ................. +2.375V to +3.60V
2.375
CC
CC
(4)
Min
3.0
0.1
0.2
45
90
0
–1.6
–1.3 V
A
) .............. –40°C to +85°C
CC
Typ
225
100
2.5
3.3
50
–1.2 V
V
JA
2.625
CC
IH
Max
1.28
V
300
110
3.6
1.7
55
uses 4-layer in
CC
–0.1
–1.1
SY58040U
Units
mA
Ω
Ω
V
V
V
V
V
V
V
V