CWR11HH106KC Kemet, CWR11HH106KC Datasheet - Page 12

• Manufacturer Part Number: CWR11HH106KC
• Description: CAP TANT 10UF 15V 10% 2312
• Manufacturer: Kemet
• Series: Military, MIL-PRF-55365/8, CWR11r
• Type: Moldedr

Specifications of CWR11HH106KC

• Capacitance: 10µF
• Voltage - Rated: 15V
• Tolerance: ±10%
• Esr (equivalent Series Resistance): 2.500 Ohm
• Operating Temperature: -55°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 2312 (6032 Metric)
• Size / Dimension: 0.236" L x 0.126" W (6.00mm x 3.20mm)
• Height - Seated (max): 0.110" (2.80mm)
• Lead Spacing: -
• Manufacturer Size Code: C
• Features: High Reliability
• Lifetime @ Temp.: -
• Lead Free Status / Rohs Status: Contains lead / RoHS non-compliant
• Other names: 1001-2238-2; T492C106K015CH7370

MIL-PRF (CWR Style) Established Reliability – T492 CWR11 Style Mil-PRF-55365/8
Figure 1 – Embossed (Plastic) Carrier Tape Dimensions
Table 4 – Embossed (Plastic) Carrier Tape Dimensions
Metric will govern
1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and
2. The tape with or without components shall pass around R without damage (see Figure 5).
3. If S
4. B
5. The cavity defi ned by A
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 [phone] • www.kemet.com
Tape Size
Tape Size
B
hole location shall be applied independent of each other.
(a) the component does not protrude above the top surface of the carrier tape.
(b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
(c) rotation of the component is limited to 20° maximum for 8 and 12mm tapes and 10° maximum for 16mm tapes (see Figure 3).
(d) lateral movement of the component is restricted to 0.5 mm maximum for 8mm and 12mm wide tape and to 1.0mm maximum for 16mm tape (see Figure 4).
(e) see Addendum in EIA Document 481 for standards relating to more precise taping requirements.
12mm
16mm
12mm
16mm
1
1
8mm
8mm
dimension is a reference dimension for tape feeder clearance only.
S
1
<1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Document 481 paragraph 4.3 (b)).
1
B
including draft concentric about B
1
is for tape feeder reference only,
T
T
Ko
T
(0.059 +0.004/-0.0)
Cover Tape
2
1
Single (4mm) &
Double (8mm)
1.5 +0.10/-0.0
Triple (12mm)
Single (4mm)
Pitch
D
0
0
, B
Center Lines of Cavity
0
and K
o
.
0
shall surround the component with suffi cient clearance that:
B
D
(0.039)
(0.059)
(0.323)
(0.476)
Note 1
Note 4
(0.171)
ØDo
1
4.35
1
12.1
8.2
1.0
1.5
User Direction of Unreeling
Max.
Min.
P
Constant Dimensions — Millimeters (Inches)
Variable Dimensions — Millimeters (Inches)
2
(0.069 ± 0.004)
1.75 ± 0.10
Po
P
1
E
(0.246)
(0.404)
(0.561)
10.25
14.25
6.25
2
E
Min.
1
tolerance on tape ±0.2 mm]
[10 pitches cumulative
Ao
ØD
1
(0.157 ± 0.004)
(0.138 ± 0.002)
(0.217 ± 0.002)
(0.217 ± 0.002)
Bo
3.5 ± 0.05
5.5 ± 0.05
5.5 ± 0.05
4.0 ± 0.10
see Note 1 Table 5
Embossment
For cavity size,
P
F
0
F
E
2
E
1
W
(0.079 ± 0.002)
(0.157 ± 0.004)
(0.315 ± 0.004)
(0.315 ± 0.004)
2.0 ± 0.05
4.0 ± 0.10
8.0 ± 0.10
8.0 ± 0.10
P
P
2
1
(0.984)
T
(0.098)
Note 2
(1.181)
(0.181)
(0.181)
R Ref.
25.0
2
2.5
4.6
4.6
30
Max
S
W Max
(0.327)
(0.484)
(0.642)
(0.024)
Note 3
0.600
12.3
16.3
1
8.3
Min.
T2006_T492 • 9/6/2011
T Max.
(0.024)
0.600
A
0
Note 5
,B
0
& K
T
(0.004)
0.100
1
Max.
0
12 12