MT48LC2M32B2TG-7:GTR Micron Technology Inc, MT48LC2M32B2TG-7:GTR Datasheet - Page 36
![](/photos/40/77/407734/tsop-ii-86_sml.jpg)
MT48LC2M32B2TG-7:GTR
Manufacturer Part Number
MT48LC2M32B2TG-7:GTR
Description
Manufacturer
Micron Technology Inc
Type
SDRAMr
Datasheet
1.MT48LC2M32B2TG-7GTR.pdf
(69 pages)
Specifications of MT48LC2M32B2TG-7:GTR
Organization
2Mx32
Density
64Mb
Address Bus
13b
Access Time (max)
17/8/5.5ns
Maximum Clock Rate
143MHz
Operating Supply Voltage (typ)
3.3V
Package Type
TSOP-II
Operating Temp Range
0C to 70C
Operating Supply Voltage (max)
3.6V
Operating Supply Voltage (min)
3V
Supply Current
160mA
Pin Count
86
Mounting
Surface Mount
Operating Temperature Classification
Commercial
Lead Free Status / Rohs Status
Not Compliant
Concurrent Auto Precharge
READ with Auto Precharge
WRITE with Auto Precharge
Figure 27:
PDF: 09005aef811ce1fe/Source: 09005aef811ce1d5
64MSDRAMx32_2.fm - Rev. J 12/08 EN
Internal
States
READ with Auto Precharge Interrupted by a READ
COMMAND
Note:
ADDRESS
BANK m
BANK n
CLK
An access command (READ or WRITE) to another bank while an access command with
auto precharge enabled is executing is not allowed by SDRAMs, unless the SDRAM
supports concurrent auto precharge. Micron SDRAMs support concurrent auto
precharge. Four cases where concurrent auto precharge occurs are defined below.
• Interrupted by a READ (with or without auto precharge): A READ to bank m will inter-
• Interrupted by a WRITE (with or without auto precharge): A WRITE to bank m will
• Interrupted by a READ (with or without auto precharge): A READ to bank m will inter-
• Interrupted by a WRITE (with or without auto precharge): A WRITE to bank m will
DQ
rupt a READ on bank n, CL later. The precharge to bank n will begin when the READ
to bank m is registered (Figure 27).
interrupt a READ on bank n when registered. DQM should be used two clocks prior to
the WRITE command to prevent bus contention. The precharge to bank n will begin
when the WRITE to bank m is registered (Figure 28 on page 37).
rupt a WRITE on bank n when registered, with the data-out appearing CL later. The
precharge to bank n will begin after
bank m is registered. The last valid WRITE to bank n will be data-in registered one
clock prior to the READ to bank m (Figure 29 on page 37).
interrupt a WRITE on bank n when registered. The precharge to bank n will begin
after
valid data WRITE to bank n will be data registered one clock prior to a WRITE to bank
m (Figure 30 on page 38).
DQM is LOW.
Page Active
T0
NOP
t
WR is met, where
READ - AP
BANK n,
Page Active
BANK n
COL a
T1
READ with Burst of 4
CL = 3 (BANK n)
T2
NOP
t
WR begins when the WRITE to bank m is registered. The last
36
BANK m,
READ - AP
T3
BANK m
COL d
Interrupt Burst, Precharge
READ with Burst of 4
t
Micron Technology, Inc., reserves the right to change products or specifications without notice.
WR is met, where
T4
CL = 3 (BANK m)
NOP
D
OUT
a
t
RP - BANK n
T5
NOP
D
a + 1
OUT
t
WR begins when the READ to
T6
NOP
D
OUT
©2001 Micron Technology, Inc. All rights reserved.
d
64Mb: x32 SDRAM
DON’T CARE
Idle
T7
NOP
t RP - BANK m
Precharge
D
d + 1
OUT
Commands