74LVC1G66GW-G NXP Semiconductors, 74LVC1G66GW-G Datasheet - Page 4

• Manufacturer Part Number: 74LVC1G66GW-G
• Description: Analog Switch Single SPST 5-Pin TSSOP T/R
• Manufacturer: NXP Semiconductors
• Type: Analog Switchr

Specifications of 74LVC1G66GW-G

• Package: 5TSSOP
• Maximum On Resistance: 195@1.95V Ohm
• Maximum Propagation Delay Bus To Bus: 0.8(Typ)@1.95V|0.4(Typ)@2.7V|0.3(Typ)@3.6V|0.2(Typ)@5.5V ns
• Maximum Low Level Output Current: 50 mA
• Maximum Turn-off Time: 4.2(Typ)@1.95V ns
• Maximum Turn-on Time: 5.3(Typ)@1.95V ns
• Switch Architecture: SPST
• Power Supply Type: Single

NXP Semiconductors
8. Limiting values
Table 5.
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
[1]
[2]
[3]
9. Recommended operating conditions
Table 6.
[1]
[2]
74LVC1G66
Product data sheet
Symbol
V
V
I
I
V
I
I
I
T
P
Symbol
V
V
V
T
Δt/ΔV
IK
SK
SW
CC
GND
stg
amb
CC
I
SW
tot
CC
I
SW
The minimum input voltage rating may be exceeded if the input current rating is observed.
The minimum and maximum switch voltage ratings may be exceeded if the switch clamping current rating is observed.
For TSSOP5 and SC-74A packages: above 87.5 °C the value of P
For XSON6 packages: above 118 °C the value of P
To avoid sinking GND current from terminal Z when switch current flows in terminal Y, the voltage drop across the bidirectional switch
must not exceed 0.4 V. If the switch current flows into terminal Z, no GND current will flow from terminal Y. In this case, there is no limit
for the voltage drop across the switch.
Applies to control signal levels.
Limiting values
Recommended operating conditions
Parameter
supply voltage
input voltage
switch voltage
ambient temperature
input transition rise and
fall rate
Parameter
supply voltage
input voltage
input clamping current
switch clamping current
switch voltage
switch current
supply current
ground current
storage temperature
total power dissipation
All information provided in this document is subject to legal disclaimers.
Conditions
V
V
Conditions
V
V
enable and disable mode
V
T
CC
CC
amb
I
I
SW
< −0.5 V or V
< −0.5 V or V
tot
= 1.65 V to 2.7 V
= 2.7 V to 5.5 V
> −0.5 V or V
= −40 ° C to +125 °C
Rev. 7 — 30 July 2010
derates linearly with 7.8 mW/K.
I
I
> V
> V
tot
SW
derates linearly with 4.0 mW/K.
CC
CC
< V
+ 0.5 V
+ 0.5 V
CC
+ 0.5 V
[1]
[2]
[2]
Min
1.65
0
0
−40
-
-
[1]
[2]
[3]
-
Min
−0.5
−0.5
−50
-
−0.5
-
−100
−65
-
Typ
-
-
-
-
-
-
74LVC1G66
Max
+6.5
+6.5
-
±50
±50
100
-
+150
250
V
CC
© NXP B.V. 2010. All rights reserved.
+ 0.5
Max
5.5
5.5
V
+125
20
10
Bilateral switch
CC
Unit
V
V
mA
mA
V
mA
mA
mA
°C
mW
Unit
V
V
V
°C
ns/V
ns/V
4 of 25