LM6588MA National Semiconductor, LM6588MA Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
LM6588MA
Manufacturer Part Number
LM6588MA
Description
Op Amps
Manufacturer
National Semiconductor
Datasheet
1.LM6588MT.pdf
(16 pages)
Specifications of LM6588MA
Number Of Channels
4
Voltage Gain Db
106 dB
Common Mode Rejection Ratio (min)
70 dB
Input Offset Voltage
4 mV at 5 V
Operating Supply Voltage
9 V, 12 V, 15 V
Supply Current
4 mA at 5 V
Maximum Operating Temperature
+ 85 C
Package / Case
SOIC-14 Narrow
Maximum Dual Supply Voltage
+/- 8 V
Minimum Operating Temperature
- 40 C
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LM6588MA.
Manufacturer:
NS/国半
Quantity:
20 000
Part Number:
LM6588MAX
Manufacturer:
NS/国半
Quantity:
20 000
Company:
Part Number:
LM6588MAX/NOPB
Manufacturer:
NS/TI
Quantity:
2 200
www.national.com
TFT Display Application
lay and slew limited response time (t = 0 to T
calculated from data sheet specifications, the small signal
settling time (T
amp’s gain vs. frequency has multiple poles, and as a result,
small-signal settling time can not be calculated as a simple
function of the op amp’s gain bandwidth. Therefore, the only
accurate method for determining op amp settling time is to
measure it directly.
The test circuit in Figure 11 was used to measure LM6588
settling time for a 2V pulse and 1kΩ load, which represents
the maximum transient amplitude and output load for a
gamma buffer. With this test system, the LM6588 settled to
within
time for a 0 to –2V pulse was slightly less, 150ns. These
values are much smaller than the desired response time of
1µs, so the LM6588 has sufficient bandwidth and slew rate
for regulating gamma line transients.
PANEL REPAIR BUFFER
It is not uncommon for a TFT panel to be manufactured with
an open in one or two of its column or row lines. In order to
repair these opens, TFT panels have uncommitted repair
lines that run along their periphery. When an open line is
identified during a panel’s final assembly, a repair line re-
routes its signal past the open. Figure 12 illustrates how a
column is repaired. The column driver’s output is sent to the
other end of an open column via a repair line, and the repair
line is driven by a panel repair buffer. When a column or row
line is repaired, the capacitance on that line increases sub-
stantially. For instance, a column typically has 50pF to
100pF of line capacitance, but a repaired column can have
up to 200pF. Column drivers are not designed to drive this
extra capacitance, so a panel repair buffer provides addi-
tional output current to the repaired column line. Note that
there is typically a 20Ω to 100Ω resistor in series with the
buffer output. This resistor isolates the output from the
200pF of capacitance on a repaired column line, ensuring
that the buffer remains stable. A pole is created by this
resistor and capacitance, but its frequency will be in the
range of 8MHz to 40MHz, so it will have only a minor effect
on the buffer’s transient response time. Panel repair buffers
transmit a column driver signal, and as mentioned in the
gamma buffer section, this signal is set by the gamma levels.
It was also mentioned that many displays have upper and
lower gamma levels that are within 500mV of the supply
FIGURE 11. Gamma Buffer Settling Time Test Circuit
±
30mV of 2V pulse in approximately 170ns. Settling
SR
to T
SET
) cannot. This is because an op
(Continued)
SR
) can be
20073436
14
rails. Therefore, op amps used as panel repair buffers should
have rail-to-rail input and stages. Otherwise, they may clip
the column driver signal.
The signal from a panel repair buffer is stored by a pixel
when the pixel’s row is selected. In high-resolution displays,
each row is selected for as little as 11µs. To insure that a
pixel has adequate time to settle-out during this brief period,
a panel repair buffer should settle to within 1% of its final
value approximately 1µs after a row is selected. This is
hardest to achieve when transmitting a column line’s maxi-
mum voltage swing, which is the difference between the
upper and lower gamma levels (i.e. voltage between VGMA1
and VGMA10). For a LM6588, the most demanding applica-
tion occurs in displays that operate from a 16V supply. In
these displays, voltage difference between the top and bot-
tom gamma levels can be as large as 15V, so the LM6588
needs to transmit a
its final value in approximately 1µs (60mV is approximately
1% of the dynamic range of the high or low polarity gamma
levels). LM6588 settling times for 15V and –15V pulses were
measured in a test circuit similar to the one in Figure 11. V
and V
measuring settling time for a 0V to 15V pulse. Likewise, V
and V
tling time for a 0V to –15V pulse. In both cases, the LM6588
output was connected to a series RC load of 51Ω and 200pF.
When tested this way, the LM6588 settled to within 60mV of
15V or –15V in approximately 1.1µs. These observed values
are very close to the desired 1µs specification, demonstrat-
ing that the LM6588 has the bandwidth and slew rate re-
quired for repair buffers in high-resolution TFT displays.
SUMMARY
This application note provided a basic explanation of how op
amps are used in TFT displays, and it also presented the
specifications required for these op amps. There are three
major op amp applications in a display: V
Gamma Buffer, and Panel Repair Buffer, and the LM6588
can be used for all of them. As a V
can supply large values of output current to regulate V
load transients. It has rail-to-rail input common-mode range
and output swing required for gamma buffers and panel
repair buffers. It also has the necessary gain bandwidth and
slew-rate for regulating gamma levels and driving column
repair lines. All these features make the LM6588 very well
suited for use in TFT displays.
−
−
were set to 0.5V and –15.5V when measuring set-
were set to 15.5V and –0.5V, respectively, when
FIGURE 12. Panel Repair Buffer
±
15V pulse and settle to within 60mV of
COM
Driver, the LM6588
COM
20073437
Driver,
COM
+
+