MP4-1Q-4LQ-00-456 Emerson Network Power, MP4-1Q-4LQ-00-456 Datasheet - Page 2

• Manufacturer Part Number: MP4-1Q-4LQ-00-456
• Manufacturer: Emerson Network Power

Specifications of MP4-1Q-4LQ-00-456

• Lead Free Status / Rohs Status: Compliant

Rated
Total
Case
Load
E L E C T R I C A L S P E C I F I C A T I O N S
Input
Input voltage .......................... 85-264 VAC
Frequency .............................. 47-440 Hz
Inrush current ......................... 40 A peak max.
Efficiency ................................ 70-80% typ. @ full case load
Power factor ........................... 0.99 typ. meets EN61000-3-2
Turn-on time ........................... AC on 1.5 sec typ.,
EMI filter standard .................. CISPR 22
EMI filter (low leakage option) .. CISPR 22
Leakage current standard ...... 2.0 mA max. @ 240 VAC
Leakage current
(low leakage option). .............. 300 A max. @ 240 VAC
Radiated EMI ......................... CISPR 22
Holdover storage .................... 20 ms minimum
AC OK .................................... >5 ms early warning min. before
Harmonic distortion ................ Meets EN61000-3-2
Isolation .................................. Meets EN60950
Global Inhibit/Enable .............. TTL, Logic “1” and Logic “0”
Input fuse (internal) ................ MP4: 10 A
Warranty ................................. 1 year
Astec Standard Power Europe
Astec House, Waterfront Business Park
Merry Hill, Dudley
West Midlands. DY5 1LX
Telephone: [phone]
Facsimile:[phone]
%
100
80
60
40
20
30
35
TA – Ambient Temperature – C
40
Power Derating Curve
45
120-350 VDC
Inhibit / Enable 150 ms typ.
EN55022 Level “B”
EN55022 Level “A”
EN55022 Level “B”
(independent of input VAC)
outputs loose regulation
Full cycle ride thru (50 Hz)
MP6: 15 A
MP8: 20 A
MP1: 20 A
50
50
Astec France S.A.R.L.
424 La Closerie, Mont D’est
93194 Noisy le Grand
France
Telephone: [phone]
Facsimile: [phone]
55
60
65
70
Normal
Air Flow
50
Astec Standard Power Germany
Robert-Heil-Str. 8
36251 Bad Hersfeld
Germany
Telephone: [phone]
Facsimile: [phone]
Output
Adjustment range ................... ±10% min. all outputs
Margining ............................... ±4-6% nom.
Overall reg .............................. 0.4% or 20 mV max.
Ripple ..................................... RMS: 0.1% or 10 mV,
Dynamic response ................. <2% or 100 mV, with 25%
Recovery time ........................ To within 1% in <300 µsec.
Overcurrent protection ........... Single, main of dual output
Short circuit protection ........... Protected for continuous short
Overvoltage protection ........... Single output modules
(measured at sense
connection)
Reverse voltage
protection ............................... 100% of rated output current
Thermal protection ................. All outputs disabled when
Remote sense ........................ Up to 0.5 V total drop
Single wire parallel ................. Current share to within 2% of
DC OK .................................... -2% to -8% of nominal for any
Minimum load ......................... Not required on single or triple
Housekeeping
Bias voltage ............................ 5 VDC @ 1A max. present
Module inhibit ......................... TTL, isolated, singles and dual
Switching frequency ............... 250 kHz
Output/Output isolation .......... >1 Megohm
VME signal option board ........ POR signal
Notes:
1 Single output modules only.
2 Single and main of dual output modules only.
3 Contact factory for optional preload if required.
www.astec.com
Astec Netherlands
Kerkenbos 10-125
Nijmegen
The Netherlands
Telephone: [phone]
Facsimile:[phone]
(36 W modules 4% max.)
whichever is greater
Pk-Pk: 1.0% or 50 mV,
whichever is greater
Bandwidth limited to 20 MHz
load step.
module 105-120% of rated
output current.
Aux output of dual output
module 105-140% of rated
output current.
Triple output module Internally
protected
circuit. Recovery is automatic
upon removal of short
2-5.5 V 122-134%
6-60 V 110-120%
Dual output module
2-6 V 122-134%
8-28 V 110-120%
Triple output module.
No overvoltage protection
provided. Recycle the AC input
voltage to reset OVP circuit
internal temp exceeds safe
operating range. >5 ms warning
(AC OK signal) before shutdown
total rated current
monitored output
output modules. 10% required
on main of dual output
modules
whenever AC input is applied
(both outputs) only
3
1
2
2
REV 25.10.00
M
M
D
U
E
W
O
P
E
R
I