SI3210M-KT Silicon Laboratories Inc, SI3210M-KT Datasheet - Page 31
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
SI3210M-KT
Manufacturer Part Number
SI3210M-KT
Description
IC SLIC/CODEC PROG 1CH 38TSSOP
Manufacturer
Silicon Laboratories Inc
Series
ProSLIC®r
Type
ProSLIC Programmable CMOS SLICr
Specifications of SI3210M-KT
Package / Case
*
Function
Subscriber Line Interface Concept (SLIC), CODEC
Interface
PCM, SPI
Number Of Circuits
1
Voltage - Supply
3.3V, 5V
Current - Supply
88mA
Power (watts)
700mW
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Includes
BORSCHT Functions, DTMF Generation and Decoding, FSK Generation, Pulse Metering Generation, Voice Loopback Test Modes
Product
Telecom
Supply Voltage (min)
3.13 V
Supply Current
4 mA
Maximum Operating Temperature
+ 100 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Number Of Channels
1
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
SI3210M-KT
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
2.1.2. Linefeed Architecture
The ProSLIC is a low-voltage CMOS device that uses
either an Si3201 linefeed interface IC or low-cost
external components to control the high voltages
required for subscriber line interfaces. Figure 17 is a
simplified illustration of the linefeed control loop circuit
for TIP or RING and the external components used.
The ProSLIC uses both voltage and current sensing to
control TIP and RING. DC and ac line voltages on TIP
and RING are measured through sense resistors R
and R
Q
base of Q
The ProSLIC measures voltage at various nodes in
order to monitor the linefeed current. R
R
sense circuitry is calibrated on-chip to guarantee
measurement
component
Calibration" on page 36 for details.
2.1.3. Linefeed Operation States
The ProSLIC linefeed has eight states of operation as
shown in Table 23. The state of operation is controlled
using the Linefeed Control register (direct Register 64).
The open state turns off all currents into the external
bipolar transistors and can be used in the presence of
fault conditions on the line and to generate Open Switch
Intervals (OSIs). TIP and RING are effectively tri-stated
with a dc output impedance of about 150 k.
The ProSLIC can also automatically enter the open
state if it detects excessive power being consumed in
the external bipolar transistors.
BAT
N
to drive TIP and RING. Q
AC
provide access to these measuring points. The
. The ProSLIC uses linefeed transistors Q
N
from the ProSLIC.
tolerances.
accuracy
DN
with
See
isolates the high-voltage
standard
"2.1.9.
DC
, R
Linefeed
external
SE
P
, and
and
Rev. 1.45
DC
See “2.1.5. Power Monitoring and Line Fault Detection”
for more details.
In the forward active and reverse active states, linefeed
circuitry is on, and the audio signal paths are powered
down.
In the forward and reverse on-hook transmission states,
audio signal paths are powered up to provide data
transmission during an on-hook loop condition.
The TIP Open state turns off all control currents to the
external bipolar devices connected to TIP and provides
an active linefeed on RING for ground start operation.
The RING Open state provides similar operation with
the RING drivers off and TIP active.
The
waveforms onto the line.
2.1.4. Loop Voltage and Current Monitoring
The ProSLIC continuously monitors the TIP and RING
voltages and external BJT currents. These values are
available in registers 78–89. Table 24 on page 33 lists
the values that are measured and their associated
registers. An internal A/D converter samples the
measured voltages and currents from the analog sense
circuitry and translates them into the digital domain. The
A/D updates the samples at a rate of 800 Hz. Two
derived values are also reported: loop voltage and loop
current. The loop voltage, V
1-bit sign, 6-bit magnitude format. For ground start
operation, the reported value is the RING voltage. The
loop current, (I
bit sign, 6-bit magnitude format. In RING open and TIP
open states, the loop current is reported as (I
(I
Q5
–I
Q6
ringing
).
Q1
state
– I
Q2
drives
+ I
Si3210/Si3211
Q5
TIP
–I
– V
Q6
programmable
)/2, is reported in a 1-
RING
, is reported as a
Q1
– I
ringing
Q2
) +
31