1-1734328-2 TE Connectivity, 1-1734328-2 Datasheet - Page 3
1-1734328-2
Manufacturer Part Number
1-1734328-2
Description
USB Connectors RCPT MINI USB AB
Manufacturer
TE Connectivity
Series
ABr
Specifications of 1-1734328-2
Product
Mini USB Type AB Connectors
Standard
USB
Size
Mini
Gender
Receptacle
Number Of Ports
1
Orientation
Right Angle
Mount Location
Top
Termination Method
Solder
Locking Feature
Without
Led
Without
Panel Ground
Without
Pcb Mount Retention Type
SMT Hold Down
Shell Plating
Nickel over Copper
Assembly Process Feature
Without Pick and Place Cover
Locating Post(s)
With
Number Of Positions
5
Contact Termination Type
Surface Mount
Contact Plating, Mating Area, Material
Gold Flash over Palladium Nickel
Contact Plating, Mating Area, Thickness (µm [?in])
0.762 [30]
Housing Color
Black
Industry Standard
USB 2.0
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Reflow solder capable to 245°C, Reflow solder capable to 260°C
Rohs/elv Compliance History
Always was RoHS compliant
Usb-if Test Id Number (tid)
Not Submitted For Testing
Applies To
Printed Circuit Board
Pcb Thickness, Recommended (mm [in])
1.57 [0.062]
Packaging Method
Tape & Reel
Lead Free Status / Rohs Status
Details
Rev
Connector Mating Force
Connector Unmating
Force
Cable Pull-out Force
Thermal Shock
Humidity Test
Temperature Life
Solderability
Resistance to Wave
Soldering Heat
Resistance to Reflow
Soldering Heat
E
TEST ITEM
3.57Kgf (35 Newtons) Max
1) Initial: 0.71Kgf (7 Newtons) Min.
2) After test: 0.31Kgf (3 Newtons) Min.
Cable shall be not dislodge from
Shall meet visual requirement, show
no physical damage.
Shall meet visual requirement, show
no physical damage.
Shall meet visual requirement, show
no physical damage.
have 95% solder coverage minimum.
No physical damage shall occur.
No physical damage shall occur.
The inspected area of each lead must
cable.
REQUIREMENTS
ENVIRONMENTAL
Figure1.
EIA 364-13
Shall be measured with TENSION
GAUGE or TENSION TESTER.
Measure force necessary to mate
assemblies at maximum rate of
12.5mm (or 0.492”) per minute.
EIA 364-13
Shall be measured with TENSION
GAUGE or TENSION TESTER.
Measure force necessary to mate
assemblies at maximum rate of
12.5mm (or 0.492”) per minute.
EIA 364-38
Apply axial load of 40 Newtons to the
cable for 1 minute.
Shall be measured with TENSION
GAUGE or TENSION TESTER in same
direction.
EIA 364-32, Test Condition I, (or
MIL-202F, Method 107G Condition A.)
Subject mated connectors to five cycles
between –55℃ to +85℃.
EIA 364-31, Test Condition A Method
III, (or MIL-202F, Method 103B Test
Condition B.)
Subject mated connectors to 168 Hours
(seven complete cycles)
EIA 364-17 Test Condition 3 Method A,
Subject mated connectors to
temperature life at 85℃ for 250hours
Steam Aging Preconditioning：
(1) Tin、Tin-Cu Coating:
93+3/-5℃、100%RH、8hrs.
<J-STD-002 category 3 aging>
(2) Other Coating:
93+3/-5℃、100%RH、1hrs.
<J-STD-002 category 2 aging>
Solder pot temperature: 245±5℃, 5sec
Solder Temp.：
Pre-soak condition, 85℃/85﹪RH for
168 hours.
Pre Heat：150~200℃, 60~180sec.
Heat：217℃ Min., 60~150sec.
Peak Temp.：260+0/-5℃, 20~40sec.
Duration：3 cycles
Tyco spec. 109-201, Condition B
265℃+/-5℃,10+2/-0sec.(For PA9T)
240℃+/-5℃,10+2/-0sec.(For PBT)
PROCEDURE
108-57062
3 of 4