LM4938MH/NOPB National Semiconductor, LM4938MH/NOPB Datasheet - Page 5

• Manufacturer Part Number: LM4938MH/NOPB
• Description: IC AMP AUDIO PWR 2.2W AB 28TSSOP
• Manufacturer: National Semiconductor
• Series: Boomer®r
• Type: Class ABr

Specifications of LM4938MH/NOPB

• Output Type: 2-Channel (Stereo) with Stereo Headphones
• Max Output Power X Channels @ Load: 2.2W x 2 @ 3 Ohm; 92mW x 2 @ 32 Ohm
• Voltage - Supply: 2.7 V ~ 5.5 V
• Features: Bass Boost, Depop, Mute, Shutdown, Thermal Protection, Volume Control
• Mounting Type: Surface Mount
• Package / Case: 28-TSSOP Exposed Pad, 28-eTSSOP, 28-HTSSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: *LM4938MH; *LM4938MH/NOPB; LM4938MH

Electrical Characteristics for Single-Ended Mode Operation
10) (Continued)
Note 3: The θ
Note 4: The θ
through 21 8mil vias.
Note 5: The θ
Note 6: The θ
Note 7: All voltages are measured with respect to the ground pins, unless otherwise specified. All specifications are tested using the typical application as shown
in Figure 1.
Note 8: When driving 3Ω loads from a 5V supply the LM4938MH must be mounted to the circuit board and forced-air cooled.
Note 9: When driving 4Ω loads from a 5V supply the LM4938MH must be mounted to the circuit board.
Note 10: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which
guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit
is given, however, the typical value is a good indication of device performance.
Note 11: The maximum power dissipation must be derated at elevated temperatures and is dictated by T
allowable power dissipation is P
can be found in the Absolute Maximum Ratings section above.
Note 12: Human body model, 100pF discharged through a 1.5kΩ resistor.
Note 13: Machine Model, 200pF – 220pF discharged through all pins.
Note 14: Typicals are measured at 25˚C and represent the parametric norm.
Note 15: Limits are guaranteed to National’s AOQL ( Average Outgoing Quality Level). Datasheet min/max specification limits are guaranteed by design, test, or
statistical analysis.
JA
JA
JA
JA
given is for an MXA28A package whose exposed-DAP is soldered to an exposed 2in
given is for an MXA28A package whose exposed-DAP is soldered to a 2in
given is for an MXA28A package whose exposed-DAP is soldered to an exposed 1in
given is for an MXA28A package whose exposed-DAP is not soldered to any copper.
DMAX
= (T
JMAX
− T
A
)/θ
JA
. For the LM4938, T
JMAX
5
= 150˚C, and the typical junction-to-ambient thermal resistance for each package
2
piece of 1 ounce printed circuit board copper on a bottom side layer
JMAX
2
2
piece of 1 ounce printed circuit board copper.
piece of 1 ounce printed circuit board copper.
, θ
JA
, and the ambient temperature T
(Notes 7,
A
. The maximum
www.national.com