TDA7563APD STMicroelectronics, TDA7563APD Datasheet - Page 17

• Manufacturer Part Number: TDA7563APD
• Description: IC AMP QUAD MULTIFUNC POWERSO36
• Manufacturer: STMicroelectronics
• Type: Class ABr

Specifications of TDA7563APD

• Output Type: 4-Channel (Quad)
• Max Output Power X Channels @ Load: 75W x 4 @ 2 Ohm
• Voltage - Supply: 8 V ~ 18 V
• Features: I²C, Mute, Short-Circuit and Thermal Protection, Standby
• Mounting Type: Surface Mount
• Package / Case: PowerSO-36 Exposed Top Pad
• Operational Class: Class-AB
• Audio Amplifier Output Configuration: 4-Channel Stereo
• Audio Amplifier Function: Speaker
• Single Supply Voltage (typ): 9/12/15V
• Dual Supply Voltage (typ): Not RequiredV
• Power Supply Requirement: Single
• Power Dissipation: 85W
• Rail/rail I/o Type: No
• Single Supply Voltage (min): 8V
• Single Supply Voltage (max): 18V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -55C to 150C
• Operating Temperature Classification: Military
• Mounting: Surface Mount
• Pin Count: 36
• Package Type: PowerSO SLUG UP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

TDA7563A
4
4.1
Output DC offset detection
Any DC output offset exceeding +/- 2 V are signalled out. This inconvenient might occur as a
consequence of initially defective or aged and worn-out input capacitors feeding a DC
component to the inputs, so putting the speakers at risk of overheating.
This diagnostic has to be performed with low-level output AC signal (or Vin = 0).
The test is run with selectable time duration by microprocessor (from a "start" to a "stop"
command):
Excess offset is signalled out if persistent throughout the assigned testing time. This feature
is disabled if any overloads leading to activation of the short-circuit protection occurs in the
process.
AC diagnostic
It is targeted at detecting accidental disconnection of tweeters in 2-way speaker and, more
in general, presence of capacitively (AC) coupled loads.
This diagnostic is based on the notion that the overall speaker's impedance (woofer +
parallel tweeter) will tend to increase towards high frequencies if the tweeter gets
disconnected, because the remaining speaker (woofer) would be out of its operating range
(high impedance). The diagnostic decision is made according to peak output current
thresholds, as follows:
To correctly implement this feature, it is necessary to briefly provide a signal tone (with the
amplifier in "play") whose frequency and magnitude are such to determine an output current
higher than 500mApk with in normal conditions and lower than 250mApk should the parallel
tweeter be missing.
The test has to last for a minimum number of 3 sine cycles starting from the activation of the
AC diagnostic function IB2<D2>) up to the I
confirm presence of tweeter, it is necessary to find at least 3 current pulses over 500mA
over all the measuring period, else an "open tweeter" message will be issued.
The frequency / magnitude setting of the test tone depends on the impedance
characteristics of each specific speaker being used, with or without the tweeter connected
(to be calculated case by case). High-frequency tones (> 10 kHz) or even ultrasonic signals
are recommended for their negligible acoustic impact and also to maximize the impedance
module's ratio between with tweeter-on and tweeter-off.
Figure 27
relevant diagnostic fields.
This feature is disabled if any overloads leading to activation of the short-circuit protection
occurs in the process.
–
–
Iout > 500mApk = NORMAL STATUS
Iout < 250mApk = OPEN TWEETER
START = Last reading operation or setting IB1 - D5 - (OFFSET enable) to 1
STOP = Actual reading operation
shows the Load Impedance as a function of the peak output voltage and the
2
C reading of the results (measuring period). To
Output DC offset detection
17/35