PS21865 MITSUBISHI, PS21865 Datasheet
PS21865
Available stocks
Related parts for PS21865
PS21865 Summary of contents
Page 1
... Detail : A (t=0.7) Heat sink side -A : Long terminal type (16.0mm) PS21865/-A PS21865/-A TRANSFER-MOLD TYPE TRANSFER-MOLD TYPE INSULATED TYPE INSULATED TYPE th generation IGBT inverter bridge for Dimensions in mm TERMINAL CODE 1. UP 14. VN1 2. VP1 15. VNC 3. VUFB 16 ...
Page 2
... When the sensed shunt voltage exceeds the SC trip-level, all the L-side IGBTs are turned OFF and a fault signal (Fo) is output. Since the SC fault may be repetitive recommended to stop the system when the Fo signal is received and check the fault Collector current waveform 0 2 PS21865/-A TRANSFER-MOLD TYPE INSULATED TYPE C2 C1 (Note 6) Protection circuit (UV) DIP-IPM H-side IGBT ...
Page 3
... Sinusoidal minute, connection pins to heat-sink plate Control Terminals Groove DIP-IPM 18mm AI board 13.5mm IGBT Chip Temp. measurement point (inside the AI board) FWDi Chip PS21865/-A TRANSFER-MOLD TYPE INSULATED TYPE Ratings 450 500 600 20 40 52.6 (Note 1) –20~+125 100 C) however, to en- f 125 100 C). ...
Page 4
... Trip level Reset level T 125 C j Trip level Reset level C = 22nF FO Applied between according to the following approximate equation : C FO PS21865/-A TRANSFER-MOLD TYPE INSULATED TYPE Limits Min. Typ. Max. — — 1.90 — — 3.00 Limits Min. Typ. Max. — 2. 1.60 — 2.20 1 ...
Page 5
... 100 C, T 125 300V 15V 10kHz CC D P.F = 0.8, sinusoidal T 125 C, T 100 between V -N (including surge) NC PS21865/-A TRANSFER-MOLD TYPE INSULATED TYPE Limits Min. Typ. Max. — 0.98 1.47 — — 65 — (Note 6) –50 100 Limits Min. Typ. Max. 0 300 400 13 ...
Page 6
... WFB V WFS HVIC1 IGBT1 Di1 COM S HVIC2 V V IGBT2 Di2 COM S HVIC3 V V IGBT3 Di3 COM S IGBT4 LVIC Di4 U OUT V CC IGBT5 Di5 V OUT U N IGBT6 Di6 OUT CIN GND CFO CFO CIN PS21865/-A TRANSFER-MOLD TYPE INSULATED TYPE DIP-IPM Jul. 2003 ...
Page 7
... C O active signal period the IGBT doesn’t turn ON SET RESET reference voltage CR circuit time constant DELAY the circuits start to operate when next input is applied. Dr RESET SET PS21865/-A TRANSFER-MOLD TYPE INSULATED TYPE . FO RESET b6 b7 Jul. 2003 ...
Page 8
... SET UV DBr c1 UV DBt line 10k Wiring inductance should be less than 10nH. width=3mm, thickness=100 m, length=17mm in copper pattern (rough standard) Shunt resistor N PS21865/-A TRANSFER-MOLD TYPE INSULATED TYPE RESET c5 c6 DIP-IPM , 2.5k (min) (Logic) Please make the connection point as close as possible to the terminal of shunt resistor ...
Page 9
... GND CFO CFO C4 Long GND wiring here might generate If this wiring is too long, the SC level noise to input and cause IGBT fluctuation might be larger and cause malfunction. SC malfunction. PS21865/-A TRANSFER-MOLD TYPE INSULATED TYPE DIP-IPM Too long wiring here might cause short-circuit CIN ...