OP07 Analog Devices, OP07 Datasheet
OP07
Specifications of OP07
Available stocks
Related parts for OP07
OP07 Summary of contents
Page 1
... Shunt current measurements Precision filters GENERAL DESCRIPTION The OP07 has very low input offset voltage (75 μV maximum for OP07E) that is obtained by trimming at the wafer stage. These low offset voltages generally eliminate any need for external nulling. The OP07 also features low input bias current (±4 nA for the OP07E) and high open-loop gain (200 V/mV for the OP07E) ...
Page 2
... Changes to Figure 26 and Figure 30............................................. 11 Replaced Figure 28 ......................................................................... 11 Changes to Applications Information Section............................ 12 Updated Outline Dimensions ....................................................... 13 Changes to Ordering Guide .......................................................... 14 8/03—Rev Rev. C Changes to OP07E Electrical Specifications ................................. 2 Changes to OP07C Electrical Specifications................................. 3 Edits to Ordering Guide .................................................................. 5 Edits to Figure 6 ................................................................................ 9 Updated Outline Dimensions ....................................................... 11 Absolute Maximum Ratings ............................................................6 Thermal Resistance ...
Page 3
... SPECIFICATIONS OP07E ELECTRICAL CHARACTERISTICS V = ±15 V, unless otherwise noted. S Table 1. Parameter INPUT CHARACTERISTICS T = 25° Input Offset Voltage 2 Long-Term V Stability OS Input Offset Current Input Bias Current Input Noise Voltage Input Noise Voltage Density Input Noise Current Input Noise Current Density Input Resistance, Differential Mode ...
Page 4
... V during the first 30 operating days are typically 2.5 μV. Refer to the Typical Performance Characteristics section. Parameter is OS sample tested. 3 Sample tested. 4 Guaranteed by design. 5 Guaranteed but not tested. OP07C ELECTRICAL CHARACTERISTICS V = ±15 V, unless otherwise noted. S Table 2. Parameter INPUT CHARACTERISTICS T = 25°C A ...
Page 5
... VOL ± load ± load kΩ P vs. the time over extended periods after the first 30 days of operation. Excluding the OS Rev Page OP07 Min Typ Max Unit ±12.0 ±13.0 V ±11.5 ±12.8 V ±12.0 V ±12 ±12.6 V 0.1 0.3 V/μs 0.4 0.6 MHz 60 Ω ...
Page 6
... Differential Input Voltage Output Short-Circuit Duration Storage Temperature Range S and P Packages Operating Temperature Range OP07E OP07C Junction Temperature Lead Temperature, Soldering (60 sec) 1 For supply voltages less than ±22 V, the absolute maximum input voltage is equal to the supply voltage. ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection ...
Page 7
... S 0°C ≤ T ≤ 70°C A 1.0 0.8 0.6 0.4 OP07C 0.2 OP07E 0 100 1k 10k MATCHED OR UNMATCHED SOURCE RESISTANCE (Ω) Figure 7. Maximum Error vs. Source Resistance ≤ 1.0V ≤ 7nA (OP07C) DIFF ±15V 25° –10 –20 –30 –30 –20 – DIFFERENTIAL INPUT VALUE (V) Figure 8 ...
Page 8
... TEMPERATURE (°C) Figure 9. Input Bias Current vs. Temperature 2 ±15V S 2.0 1.5 1.0 OP07C 0.5 OP07E 0 –100 –75 –50 – TEMPERATURE (°C) Figure 10. Input Offset Current vs. Temperature REFERRED TO INPUT 5mV/CM AT OUTPUT TIME (1s/DIV) Figure 11. Low Frequency Noise 1000 100 ...
Page 9
... Figure 19. Maximum Output Swing vs. Frequency ±15V 25° 10M 100 Figure 20. Maximum Output Voltage vs. Load Resistance Rev Page ±15V 25°C A 100 1k 10k 100k 1M FREQUENCY (Hz ±15V 25°C A 10k 100k FREQUENCY (Hz) = ±15V = ±10mV = 25°C POSITIVE SWING NEGATIVE SWING 1k LOAD RESISTANCE TO GROUND (Ω) OP07 10M 1M 10k ...
Page 10
... Figure 24. Trimmed Offset Voltage vs. Temperature 16 12 0.3µV/MONTH 8 TREND LINE 0.2µV/MONTH 0.3µV/MONTH 4 TREND LINE TREND LINE 0 0.3µV/MONTH TREND LINE –4 –8 –12 – TIME (Months) Figure 25. Offset Voltage Drift vs. Time OP07C OP07E 75 100 0.2µV/MONTH TREND LINE 0.2µV/MONTH TREND LINE ...
Page 11
... FD333 D2 4 V– R2 V– 10kΩ Figure 29. Burn-In Circuit RF R1 SUM MODE BIAS 3kΩ 2 – 7 OP07C 2 – 10kΩ OP07C + 100kΩ V– V– – NOTES 1. PINOUT SHOWN FOR P PACKAGE Figure 30. High Speed, Low V Composite Amplifier OS R4 10kΩ R1 10kΩ ...
Page 12
... V A NOTES 1. PINOUT SHOWN FOR P PACKAGE Figure 33. Precision Absolute-Value Circuit APPLICATIONS INFORMATION The OP07 provides stable operation with load capacitance 500 pF and ±10 V swings; larger capacitances should be decoupled with a 50 Ω decoupling resistor Stray thermoelectric voltages generated by dissimilar metals at the contacts to the input terminals can degrade drift ...
Page 13
... Figure 35. 8-Lead Plastic Dual-in-Line Package [PDIP] P-Suffix (N-8) Dimensions shown in inches and (millimeters) Rev Page 0.50 (0.0196) 45° 0.25 (0.0099) 1.27 (0.0500) 0.40 (0.0157) 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) 0.195 (4.95) 0.130 (3.30) 0.115 (2.92) 0.014 (0.36) 0.010 (0.25) 0.008 (0.20) 0.430 (10.92) MAX OP07 ...
Page 14
... OP07CP −40°C to +85°C OP07CPZ 1 −40°C to +85°C OP07CS −40°C to +85°C OP07CS-REEL −40°C to +85°C OP07CS-REEL7 −40°C to +85°C OP07CSZ 1 −40°C to +85°C OP07CSZ-REEL 1 −40°C to +85°C OP07CSZ-REEL7 1 −40°C to +85° Pb-free part ...
Page 15
... NOTES Rev Page OP07 ...
Page 16
... OP07 NOTES ©2006 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C00316-0-7/06(D) Rev Page ...