TDA7575PDTR STMicroelectronics, TDA7575PDTR Datasheet - Page 12

• Manufacturer Part Number: TDA7575PDTR
• Description: IC AMP AUDIO PWR 150W POWERSO37
• Manufacturer: STMicroelectronics
• Type: Class ABr

Specifications of TDA7575PDTR

• Output Type: 1-Channel (Mono) or 2-Channel (Stereo)
• Max Output Power X Channels @ Load: 150W x 1 @ 1 Ohm; 75W x 2 @ 2 Ohm
• Voltage - Supply: 8 V ~ 18 V
• Features: Differential Inputs, I²C, Mute, Short-Circuit and Thermal Protection, Standby
• Mounting Type: Surface Mount
• Package / Case: PowerSO-36 Exposed Top Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-3990-2

DOCUMENT CD00003142
Copyright STMicroelectronics
TDA7575PD
It is recommended to minimize the impedance on the board between OUT2 and the load in order to minimize
THD distortion. It is also recommended to control the maximum mismatch impedance between VCC pins
(PIN21/PIN22 respect to PIN33/PIN34) and between PWGND pins (PIN24/PIN25 respect to PIN30/PIN31),
mismatch that must not exceed a value of 20 mOhm.
With 1OHM feature settled the active input is IN2 (PIN17 and PIN18), therefore IN1 pins should be let floating.
It is possible to set the load capability acting on 1OHM pin as follows:
1OHM PIN (PIN15) < 1.5V: two channels mode (for a minimum load of 2 OHM)
1OHM PIN (PIN15) > 2.5V: one channel mode (for 1 OHM load).
IT IS TO REMEMBER THAT 1 0HM FUNCTION IS A HARDWARE SELECTION.
Therefore it is recommended to leave 1OHM PIN floating or shorted to GND to set the two channels mode con-
figuration, or to short 1OHM PIN to VCC to set the one channel (1OHM) configuration.
I
It is possible to disable the I
the usual ST-BY and MUTE pins. In order to activate or deactivate this feature, I
I2C PIN (PIN16) < 1.5V: I
I2C PIN (PIN16) > 2.5V: I
It is also possible to let I
it.
In particular:
I
The amplifier can always be switched off by putting Vstby to 0V, but with I
through I
I
For both STD and HE MODE the play/mute mode can be set acting on Vmute pin.
8/17
2
2
2
C Abilitation Setting
C ENABLED: I
C DISABLED: I
– STD MODE: Vstby (PIN5) > 3.5V, IB2(D1)=0
– HE MODE: Vstby (PIN5) > 3.5V, IB2(D1)=1
– PLAY MODE: Vmute (pin 4) >3.5V, IB1 (D2) = 1
– STD MODE: 3.5V < stby (PIN5) < 5
– HE MODE: Vstby (PIN5) > 7V
– PLAY MODE: Vmute (pin 4) >3.5V
2
C (with Vstby>3.5V).
REVISION 3.0
2
2
C pin (PIN16) > 2.5V
C pin (PIN16) < 1.5V
2
C PIN floating to deactivate the I
2
2
C bus interface deactivated
C bus interface activated
2
C interface by acting on I
COMPANY INTERNAL
ACTIVE
2
C PIN (PIN16) and control the TDA7575PD by means of
2
C bus interface, or to short I
2
C enabled it can be turn on only
Unauthorized reproduction and communication strictly prohibited
2
C PIN must be set as follows:
2
C PIN to VCC to activate
DATE 22-Mar-2004
page: 8/17