MAX9750BETI+ Maxim Integrated Products, MAX9750BETI+ Datasheet - Page 15
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX9750BETI+
Manufacturer Part Number
MAX9750BETI+
Description
IC AMP AUDIO PWR 2.6W AB 28TQFN
Manufacturer
Maxim Integrated Products
Series
DirectDrive™r
Type
Class ABr
Datasheet
1.MAX9750AEUI.pdf
(30 pages)
Specifications of MAX9750BETI+
Output Type
2-Channel (Stereo) with Stereo Headphones
Max Output Power X Channels @ Load
2.6W x 2 @ 3 Ohm; 110mW x 2 @ 16 Ohm
Voltage - Supply
4.5 V ~ 5.5 V
Features
Depop, Short-Circuit and Thermal Protection, Shutdown, Volume Control
Mounting Type
Surface Mount
Package / Case
28-TQFN Exposed Pad
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Table 1. MAX9750 Maximum Gain Settings
Table 2. MAX9751/MAX9755 Gain Settings
The MAX9750 features an audible alert beep input
(BEEP) that accepts a mono system alert signal and
mixes it into the stereo audio path. When the amplitude
of V
frequency of the beep signal is greater than 300Hz, the
beep signal is mixed into the active audio path (speaker
or headphone). If the signal at V
< 800mV
into the audio path. The amplitude of the BEEP signal at
the device output is roughly the amplitude of V
times the gain of the selected signal path.
The input resistor (R
amplifier, and thus the amplitude of V
R
where R
resistor (47kΩ) and V
Note that the BEEP amplifier can be set up as either an
attenuator, if the original alert signal amplitude is too
large, or set to gain up the alert signal if it is below
800mV
the value of the coupling capacitor as described in the
Input Filtering section. Multiple beep inputs can be
summed (Figure 8).
B
GAIN2
based on:
BEEP(OUT)
0
0
1
1
GAIN
P-P
0
1
INT
P-P
. AC couple the alert signal to BEEP. Choose
GAIN1
is the value of the BEEP amplifier feedback
or < 300Hz, the BEEP signal is not mixed
0
1
0
1
exceeds 800mV
R
2.6W Stereo Audio Power Amplifiers and
______________________________________________________________________________________
SPEAKER MODE
B
B
GAIN (dB)
) sets the gain of the BEEP input
≤
IN
MAX9750A
10.5
V
is the BEEP input amplitude.
9
IN
10.5
13.5
12
9
0 3
×
.
R
P-P
INT
SPEAKER MODE GAIN (dB)
DirectDrive Headphone Amplifiers
BEEP(OUT)
(Figure 8) and the
BEEP(OUT)
MODE GAIN (dB)
HEADPHONE
BEEP Input
MAX9750B
16.5
19.5
15
18
BEEP(OUT)
3
0
. Choose
is either
MAX9750C
The MAX9751 features a 2:1 input multiplexer on each
amplifier, allowing input selection between two stereo
sources. The logic input IN1/2 controls both multiplex-
ers. A logic high selects input IN_1 and a logic low
selects input IN_2.
The MAX9750/MAX9751/MAX9755 features a 0.2µA,
low-power shutdown mode that reduces quiescent cur-
rent consumption and extends battery life. Driving
SHDN low disables the drive amplifiers, bias circuitry,
and charge pump, and drives BIAS and all outputs to
GND. Connect SHDN to V
The MAX9750/MAX9751/MAX9755 speaker amplifiers
feature Maxim’s comprehensive, industry-leading click-
and-pop suppression. During startup, the click-pop
suppression circuitry eliminates any audible transient
sources internal to the device. When entering shut-
down, both amplifier outputs ramp to GND quickly and
simultaneously.
Figure 6. Volume Control Circuit
10.5
7.5
6
9
V
REF
DAC
HEADPHONE MODE GAIN (dB)
Click-and-Pop Suppression
DD
HPV
VOL
for normal operation.
DD
MAX9750
Input Multiplexer
0
0
3
3
Speaker Amplifier
Shutdown
15