MAX9760ETI+T Maxim Integrated Products, MAX9760ETI+T Datasheet - Page 16
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX9760ETI+T
Manufacturer Part Number
MAX9760ETI+T
Description
IC AMP AUDIO PWR 3W STER 28TQFN
Manufacturer
Maxim Integrated Products
Type
Class ABr
Datasheet
1.MAX9760EUI.pdf
(31 pages)
Specifications of MAX9760ETI+T
Output Type
2-Channel (Stereo) with Stereo Headphones
Max Output Power X Channels @ Load
3W x 2 @ 3 Ohm; 200mW x 2 @ 16 Ohm
Voltage - Supply
4.5 V ~ 5.5 V
Features
Depop, I²C, Input Multiplexer, Mute, Shutdown, Thermal Protection
Mounting Type
Surface Mount
Package / Case
28-TQFN Exposed Pad
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Stereo 3W Audio Power Amplifiers with
Headphone Drive and Input Mux
Figure 5. Early STOP Condition
Figure 6. Slave Address Byte Definition
MAX9762. The master terminates transmission by issu-
ing the STOP condition, this frees the bus. If a REPEAT-
ED START condition is generated instead of a STOP
condition, the bus remains active.
The MAX9760/MAX9762 recognize a STOP condition at
any point during the transmission except if a STOP con-
dition occurs in the same high pulse as a START condi-
tion (Figure 5). This condition is not a legal I
at least one clock pulse must separate any START and
STOP conditions.
A REPEATED START (S
change of data direction on the bus. Such a change
occurs when a command word is required to initiate a
read operation. S
master is writing to several I
want to relinquish control of the bus. The MAX9760/
MAX9762 serial interface supports continuous write
operations with or without an S
them. Continuous read operations require S
because of the change in direction of data flow.
16
______________________________________________________________________________________
S
SDA
SCL
SDA
SCL
A6
ILLEGAL EARLY STOP CONDITION
A5
LEGAL STOP CONDITION
START
r
STOP
may also be used when the bus
A4
REPEATED START Conditions
r
A3
) condition may indicate a
START
ILLEGAL
2
STOP
C devices and does not
Early STOP Conditions
A2
r
condition separating
A1
A0
r
2
conditions
R/W
C format,
The acknowledge bit (ACK) is the ninth bit attached to
any 8-bit data word. The receiving device always gen-
erates ACK. The MAX9760/MAX9762 generate an ACK
when receiving an address or data by pulling SDA low
during the night clock period. When transmitting data,
the MAX9760/MAX9762 wait for the receiving device to
generate an ACK. Monitoring ACK allows for detection
of unsuccessful data transfers. An unsuccessful data
transfer occurs if a receiving device is busy or if a sys-
tem fault has occurred. In the event of an unsuccessful
data transfer, the bus master should reattempt commu-
nication at a later time.
The bus master initiates communication with a slave
device by issuing a START condition followed by a 7-bit
slave address (Figure 6). When idle, the MAX9760/
MAX9762 wait for a START condition followed by its
slave address. The LSB of the address word is the
Read/Write (R/W) bit. R/W indicates whether the master
is writing to or reading from the MAX9760/MAX9762
(R/W = 0 selects the write condition, R/W = 1 selects
the read condition). After receiving the proper address,
the MAX9760/MAX9762 issue an ACK by pulling SDA
low for one clock cycle.
The MAX9760/MAX9762 have a factory-/user-pro-
grammed address. Address bits A6–A2 are preset,
while A0 and A1 is set by ADD. Connect ADD to either
V
slave address
There are three registers that configure the
MAX9760/MAX9762: the MUTE register, SHDN register,
and control register. In write data mode (R/W = 0), the
register address and data byte follow the device
address (Figure 7).
The MUTE register (01hex) is a read/write register that
sets the MUTE status of the device. Bit 3 (MUTEL) of
the MUTE register controls the left channel, bit 4
(MUTER) controls the right channel. A logic high mutes
the respective channel, a logic low brings the channel
out of mute.
The SHDN register (02hex) is a read/write register that
controls the power-up state of the device. A logic high
in bit 0 of the SHDN register shuts down the device; a
logic low turns on the device. A logic high is required in
bits 2 to 7 to reset all registers to their default settings.
DD
, GND, SCL, or SDA to change the last 2 bits of the
(Table
2).
Acknowledge Bit (ACK)
Write Data Format
MUTE Register
SHDN Register
Slave Address