V375A24H600BL2 Vicor Corporation, V375A24H600BL2 Datasheet
V375A24H600BL2
Related parts for V375A24H600BL2
V375A24H600BL2 Summary of contents
Page 1
RoHS Compliant (with pin option) DC input range: 250 – 425 V Input surge withstand: 500 V for 100 ms DC output: 2 – Programmable output 110% Regulation: ±0.25% no load to full ...
Page 2
Electrical characteristics apply over the full operating range of input voltage, output load (resistive) and baseplate temperature, unless otherwise specified. All temperatures refer to the operating temperature at the center of the baseplate. Operating input voltage 250 Input surge withstand ...
Page 3
Primary Control Parallel) PC bias voltage 5.50 current limit 1.5 PC module disable 2.3 PC module enable delay PC module alarm PC resistance 0.9 PR emitter amplitude 5.7 PR emitter current 150 PR receiver impedance 375 ...
Page 4
Efficiency 72 Ripple and noise Output OVP setpoint 2.7 Dissipation, standby Load regulation Load current 0 Current limit 81.6 Short circuit current 56 Efficiency 79.4 Ripple and noise Output OVP setpoint 4.14 Dissipation, standby Load regulation Load current 0 Current ...
Page 5
Efficiency 82 Ripple and noise Output OVP setpoint 6.03 Dissipation, standby Load regulation Load current 0 Current limit 61.2 Short circuit current 42 Efficiency 81.6 Ripple and noise Output OVP setpoint 9.55 Dissipation, standby Load regulation Load current 0 Current ...
Page 6
Efficiency 85 Ripple and noise Output OVP setpoint 13.7 Dissipation, standby Load regulation Load current 0 Current limit 33.9 Short circuit current 23.3 Efficiency 85.5 Ripple and noise Output OVP setpoint 17.1 Dissipation, standby Load regulation Load current 0 Current ...
Page 7
Efficiency 86.5 Ripple and noise Output OVP setpoint 27.1 Dissipation, standby Load regulation Load current 0 Current limit 17 Short circuit current 5 Efficiency 86.8 Ripple and noise Output OVP setpoint 31.5 Dissipation, standby Load regulation Load current 0 Current ...
Page 8
Efficiency 86.8 Ripple and noise Output OVP setpoint 40.4 Dissipation, standby Load regulation Load current 0 Current limit 17 Short circuit current 11.6 Efficiency 85.8 Ripple and noise Output OVP setpoint 40.4 Dissipation, standby Load regulation Load current 0 Current ...
Page 9
Efficiency 87 Ripple and noise Output OVP setpoint 53.7 Dissipation, standby Load regulation Load current 0 Current limit 8.49 Short circuit current 5.83 Efficiency 87.7 Ripple and noise Output OVP setpoint 60.4 Dissipation, standby Load regulation Load current 0 Current ...
Page 10
The module may be disabled by pulling PC below 2.3 V with respect to the –Input. This may be done with an open collec- tor transistor, relay, or optocoupler. Multiple converters may be disabled with a single transistor or relay ...
Page 11
The output voltage of the converter can be adjusted or programmed via fixed resistors, potentiometers or voltage DACs. See Figures 7 and 8. +OUT +S Error SC Amp –S 0.033 μF 1 kΩ –OUT 1.23 V 1,000 Vout R (ohms) ...
Page 12
The PR pin supports paralleling for increased power with N+1 (N+M) redundancy and phased array capability. Modules of the same input voltage, output voltage, and power level will current share if all PR pins are suitably interfaced. Compatible interface architectures ...
Page 13
Module 1 SC –S –S –OUT +S +OUT +S +S Module 2 Load SC –S –S –OUT –S +OUT +S Module N+1 SC –S –OUT Figure 11 — N+1 module array output connections. (None) Short Tin/Lead L ...
Page 14
No. Function Label 1 +In + Primary 2 PC Control 3 Parallel PR 4 –In – 5 –Out – 6 –Sense –S Secondary 7 SC Control 8 +Sense +S 9 +Out + Figure 13 — Module outline 0.062 ±0.010 PCB ...
Page 15
Vicor products are guaranteed for two years from date of shipment against defects in material or workmanship when in normal use and service. This warranty does not extend to products subjected to misuse, accident, or improper application or maintenance. Vicor ...