AC16DGM Teccor Electronics, AC16DGM Datasheet - Page 50

• Manufacturer Part Number: AC16DGM
• Manufacturer: Teccor Electronics

Alternistor Triacs
(10) See Figure E4.12 for t
(11) See package outlines for lead form configurations. When ordering
(12) Initial on-state current = 400 mA dc for 16 A to 40 A devices and
(13) See Figure E4.1 through Figure E4.4 for maximum allowable case
(14) Pulse width 10 µs;
(15) For 6 A to 12 A devices, R
(16) 40 A pin terminal leads on K package can run 100 °C to 125 °C.
(17) Alternistor does not turn on in Quadrant IV.
(18) T
(19) I
(20) Minimum non-trigger V
Gate Characteristics
Teccor triacs may be turned on in the following ways:
•
•
In all cases, if maximum surge capability is required, gate pulses
should be a minimum of one magnitude above minimum I
with a steep rising waveform ( 1 µs rise time).
If QIV and QI operation is required (gate always positive), see
Figure AN1002.8, “Amplified Gate” Thyristor Circuit.
* UL Recognized Product per UL File E71639
** For 4000 V isolation, use V suffix in part number.
http://www.teccor.com
[phone]
Package Code
In-phase signals (with standard AC line) using Quadrants I
and III
Application of unipolar pulses (gate always negative), using
Quadrants II and III with negative gate pulses
special lead forming, add type number as suffix to part number.
100 mA for 6 A to 12 A devices.
temperature at maximum rated current.
devices with gate pulse having rise time of 0.1 µs.
GT
C
Type
10 A
12 A
16 A
25 A
30 A
35 A
40 A
= T
= 200 mA for 6 A to 12 A devices and 500 mA for 16 A to 40 A
6 A
8 A
J
for test conditions in off state
I
GT
Isolated *
TO-218
gt
GT
1.35
0.97
versus I
K
I
at 125 °C is 0.2 V.
GTM
L
= 60 ; 16 A and above, R
GT
.
TO-218X
Isolated *
1.32
0.95
J
Thermal Resistance (Steady State)
L
R
= 30
GT
JC
rating
Isolated **
TO-220
3.3 [50]
[R
2.8
2.6
2.3
2.1
2.0
2.3
L
E4 - 6
JA
] (TYP. C/W
Definition of Quadrants
Electrical Isolation
Teccor’s isolated alternistor packages withstand a minimum high
potential test of 2500 V ac rms from leads to mounting tab, over
the operating temperature range of the device. The following iso-
lation table shows standard and optional isolation ratings.
* UL Recognized File E71639
** For 4000 V isolation, use V suffix in part number.
V AC RMS
2500
4000
Non-Isolated
1.80 [45]
I
TO-220
G T
1.50
1.30
1.20
1.10
0.87
0.85
R
(
(
-
-
-
)
)
I
GATE
I
GATE
G T
G T
ALL POLARITIES ARE REFERENCED TO MT1
NOTE: Alternistors will not operate in QIV
from Leads to Mounting Tab *
REF
REF
MT2
Isolated
Standard
MT2
TO-218
MT1
MT1
N/A
Electrical Isolation
(Negative Half Cycle)
(Positive Half Cycle)
TO-252
D-Pak
MT2 NEGATIVE
2.1
1.8
MT2 POSITIVE
D
QIII
QII
+
-
QI
QIV
Optional **
(+)
(+)
Isolated
Standard
TO-220
I
GATE
I
GATE
G T
G T
2.3 [64]
TO-251
V-Pak
©2002 Teccor Electronics
Thyristor Product Catalog
2.1
V
MT2
REF
MT2
REF
MT1
MT1
+
TO-218X
Isolated
Standard
I
Data Sheets
G T
TO-263
D
N/A
1.80
1.50
1.30
1.20
1.10
0.87
2
N
Pak