PH50S48-28 TDK Corporation, PH50S48-28 Datasheet - Page 48
![no-image](/images/manufacturer_photos/0/6/653/tdk_corporation_sml.jpg)
PH50S48-28
Manufacturer Part Number
PH50S48-28
Description
Manufacturer
TDK Corporation
Datasheet
1.PH50S48-28.pdf
(58 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PH50S48-28
Manufacturer:
LAMBDA
Quantity:
37
Company:
Part Number:
PH50S48-28
Manufacturer:
LAMBDA
Quantity:
228
Part Number:
PH50S48-28
Quantity:
60
PH
B-346
PH
Reversed Connection of Input
An error of reverse (+,−electrodes) input may cause of
damage of the power module. If there is possibility to con-
nect the module conversely by accident, it is necessary to
attach a protective diode and an input fuse.
The rating voltage of the diode shall be higher than input
voltage, and the maximum in-rush current shall be higher
than fuse.
2 Output Voltage Range
Output voltage can be adjusted within±10% (3.3V, 5V,
the external trimmer (variable resistor). However, if the out-
put voltage become over the above range, OVP activates.
There is a limit of input voltage shown in Figure2-1 when
the output voltage trims high.
48V : -10% to +20% ) of the nominal voltage by adjusting
Figure1-5 Protection for Reversed Connection of Input
12 0
11 0
12 0
10 0
11 0
10 0
12 0
11 0
12 0
10 0
11 0
10 0
9 0
9 0
9 0
9 0
300S, 600S
Fuse
Figure2-1 Limit of Input Voltage
2 0 0
2 0 0
3 5
3 5
3 6
3 6
(280VDC Input)
+Vin
−Vin
(48VDC Input)
12V, 15V, 24V, 48V Output
12V, 15V, 24V, 48V Output
12V, 15V, 24V, 48V Output
12V, 15V, 24V, 48V Output
12V, 15V, 24V, 48V Output
12V, 15V, 24V, 48V Output
12V, 15V, 24V, 48V Output
12V, 15V, 24V, 48V Output
2 2 0
2 2 0
4 0
Input Voltage (VDC)
4 0
Input Voltage (VDC)
Input Voltage (VDC)
Input Voltage (VDC)
3.3V, 5V, 48V Output
3.3V, 5V, 48V Output
3.3V, 5V, 48V Output
3.3V, 5V, 48V Output
3.3V, 5V, 48V Output
3.3V, 5V, 48V Output
3.3V, 5V, 48V Output
3.3V, 5V, 48V Output
2 4 0
2 4 0
4 5
4 5
+V
−V
2 6 0
2 6 0
5 0
5 0
2 8 0
2 8 0
Load
5 5
5 5
Connection method of external resistor (R1) and variable
resistor (VR) is shown as follow.
External Resistor : below±5% Tolerance
Variable Resistor : below±20% Tolerance
below 1% of Remain
-10%~ +20% Variable (3.3V, 5V, 48V)
±10% Variable(12V, 15V, 24V, 28V)
3 Maximum Output Ripple and Noise
Maximum output ripple and noise is measured by a method
based on JEITA-9141.
The connection is shown as Figure3-1. Attach capacitors
(C4: Ceramic Capacitor: 2.2μF, C5: Electrolytic Capaci-
tor: Refer to Table1-2) 50mm from the output for PH300S
and as short as possible to the output terminal for PH600.
Also, attach a coaxial cable with JEITA attachment at the
both side of C4 capacitor shown as Figure3-1. Oscillo-
scope shall be used at a range of 100MHz bandwidth.
The output ripple voltage and the output spike noise volt-
age may be changed for the design of printed circuit board.
For 48V output model, avoid to reduce the output voltage
below -10% cause damage of the module
Variable
Table2-1 External Resistor and Variable Resistor Output
Range
Figure2-2 Example Connection of External Resistance
Figure 3-1 Measurement of Maximum Output Ripple &
R1
VR
+V
−V
50mm
3.3V
4.7k
2k
− 10%
+ 20%
Noise (Example: PH300S)
TRM
+S
+V
−V
−S
4.7k
5V
5k
+
・All specifications are subject to change without notice.
12V
30k
R1
5k
Coaxial Cable
JEITA
Attachment
R:50Ω
C:4700pF
VR
as short as possible
1.5m 50Ω
15V
33k
10k
± 10%
Load
24V
68k
10k
+
−
Load
28V
68k
20k
Oscilloscope
− 10%
+ 20%
220k
48V
30k