JC050H Lineage Power, JC050H Datasheet - Page 8

• Manufacturer Part Number: JC050H
• Manufacturer: Lineage Power

dc-dc Converters; 18 to 36 Vdc Input, 24 Vdc Output; 50 W to 100 W
Test configurations
Note: All measurements are taken at the module terminals. When
Figure 13. Output Voltage and Efficiency
Design Considerations
Input Source Impedance
The power module should be connected to a low
ac-impedance input source. Highly inductive source
impedances can affect the stability of the power mod-
ule. For the test configuration in Title 11, a 33 µF elec-
trolytic capacitor (ESR < 0.7 Ω at 100 kHz) mounted
close to the power module helps ensure stability of the
unit. For other highly inductive source impedances,
consult the factory for further application guidelines.
Safety Considerations
For safety-agency approval of the system in which the
power module is used, the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standard,
i.e., UL-1950, CSA 22.2-950, and EN60950.
For the converter output to be considered meeting the
requirements of safety extra-low voltage (SELV), the
input must meet SELV requirements.
If the input meets extra-low voltage (ELV) require-
ments, then the converter’s output is considered ELV.
The input to these units is to be provided with a maxi-
mum 20 A normal-blow fuse in the ungrounded lead.
Electrical Descriptions
8 8
SUPPLY
η
RESISTANCE
socketing, place Kelvin connections at module terminals to
avoid measurement errors due to socket contact resistance.
CONTACT
=
⎛
⎝
[
--------------------------------------------- -
V
[
Measurement Test Setup
V
O
I
I
I
(+) V
(+) V
–
–
V
V
O
I
I
I
(+)
(
(–)
–
(–)
)
]I
]I
SENSE(+)
I
SENSE(
O
⎞
⎠
(continued)
V
V
×
O
O
(
(+)
–
–
100
)
)
DISTRIBUTION LOSSES
I
O
CONTACT AND
LOAD
8-749 (C)
Current Limit
To provide protection in a fault (output overload) condi-
tion, the unit is equipped with internal current-limiting
circuitry and can endure current limiting for an unlim-
ited duration. At the point of current-limit inception, the
unit shifts from voltage control to current control. If the
output voltage is pulled very low during a severe fault,
the current-limit circuit can exhibit either foldback or tai-
lout characteristics (output current decrease or
increase). The unit operates normally once the output
current is brought back into its specified range.
Feature Descriptions
Remote On/Off
Two remote on/off options are available. Positive logic
remote on/off turns the module on during a logic high
voltage on the ON/OFF pin, and off during a logic low.
Negative logic remote on/off turns the module off dur-
ing a logic high and on during a logic low. Negative
logic (code suffix “1”) is the factory-preferred configura-
tion.
To turn the power module on and off, the user must
supply a switch to control the voltage between the on/
off terminal and the V
can be an open collector or equivalent (see Title 14). A
logic low is V
during a logic low is 1 mA. The switch should maintain
a logic-low voltage while sinking 1 mA.
During a logic high, the maximum V
the power module is 15 V. The maximum allowable
leakage current of the switch at V
If not using the remote on/off feature, do one of the fol-
lowing:
n
n
For negative logic, short ON/OFF pin to V
For positive logic, leave ON/OFF pin open.
on/off
= 0 V to 1.2 V. The maximum I
I
(-) terminal (V
on/off
on/off
on/off
= 15 V is 50 μA.
). The switch
Lineage Power
March 2008
generated by
I
(-).
on/off