PKJ4711EPI Ericsson Microelectronics, PKJ4711EPI Datasheet
PKJ4711EPI
Related parts for PKJ4711EPI
PKJ4711EPI Summary of contents
Page 1
Key Features • Industry standard Half-brick 58x61x8.5 mm (2.3x2.4x0.33 in) • Low profi le, max 8.5 mm (0.33 in) • Design for environment in a cost effi cient open-frame design • High effi ciency, typ 3.3 Vout ...
Page 2
Absolute Maximum Ratings Characteristics T Maximum Operating Pcb Temperature Pcb T Storage temperature S V Input voltage I V Isolation voltage (input to output test voltage) ISO V Input voltage transient for 100 Negative logic RC V ...
Page 3
Mechanical Data Bottom view 4.80 [.19] 53.10 [2.09] 57.90 [2.28] Dimensions in mm [in.] Comp. 1.83 [.07] 1.02 [.04 3.60 [.14] or 5.30 [.21] depending on choice of pin length Recommended Footprint (Component side) ...
Page 4
PKJ 4719E PI Output T = –40…+125° ...75V, sense pins connected to output pins unless otherwise specifi ed. Pcb I Characteristics Output voltage initial setting and accuracy V Oi Output adjust range Output voltage tolerance band Idling ...
Page 5
PKJ 4719E PI Typical Characteristics Effi ciency [%] Effi ciency vs. load current and input voltage at T Output Characteristic [V] 2.7 2.6 2.5 ...
Page 6
PKJ 4719E PI Typical Characteristics Output Ripple Output voltage ripple (50mV/div Io=30A resistive load. Band width=4MHz. Time scale: 2µs / div. Output Voltage Adjust The resistor value for an adjusted output voltage is calculated by using the following ...
Page 7
PKJ 4810E PI Output T = –40…+125° ...75V, sense pins connected to output pins unless otherwise specifi ed. Pcb I Characteristics Output voltage initial setting and accuracy V Oi Output adjust range Output voltage tolerance band Idling ...
Page 8
PKJ 4810E PI Typical Characteristics Effi ciency [%] Effi ciency vs. load current and input voltage at T Output Characteristic [V] 3.5 3.4 3.3 3.2 ...
Page 9
PKJ 4810E PI Typical Characteristics Output Ripple Output voltage ripple (50mV/div Io=25A resistive load. Band width=4MHz. Time scale: 1µs / div. Output Voltage Adjust The resistor value for an adjusted output voltage is calculated by using the following ...
Page 10
PKJ 4111 E PI Output T = –40…+125° ...75V, sense pins connected to output pins unless otherwise specifi ed. Pcb I Characteristics Output voltage initial setting and accuracy V Oi Output adjust range Output voltage tolerance band ...
Page 11
PKJ 4111E PI Typical Characteristics Effi ciency [%] Effi ciency vs. load current and input voltage at T Output Characteristic [V] 5.2 5.1 5.0 4.9 ...
Page 12
PKJ 4111E PI Typical Characteristics Output Ripple Output voltage ripple (50mV/div Io=20A resistive load. Band width=4MHz. Time scale: 1µs / div. Output Voltage Adjust The resistor value for an adjusted output voltage is calculated by using the following ...
Page 13
EMC Specifi cation The conducted EMI measurement was performed using a module placed directly on the test bench. The fundamental switching frequency is 140kHz for PKJ 4810E 53V (0.1...1.0) × Conducted ...
Page 14
Operating Information Input Voltage The input voltage range 36…75Vdc meets the requirements of the European Telecom Standard ETS 300 132-2 for normal input voltage range in –48V and –60V DC systems, -40.5…- 57.0V and –50.0…-72V respectively. At input voltages exceeding ...
Page 15
Operating Information Current Limit Protection The PKJ 4000E Series DC/DC converters include current limiting circuitry that allows them to withstand continuous overloads or short circuit conditions on the output. The output voltage will decrease towards zero for output currents in ...
Page 16
Thermal Consideration General The PKJ 4000E Series DC/DC converters are designed to operate in a variety of thermal environments, however sufficient cooling should be provided to help ensure reliable operation. Heat is removed by conduction, convection and radiation to the ...
Page 17
Miscellaneous Soldering Information The PKJ 4000E Series DC/DC converters are intended for through hole mounting on a PCB. When wave soldering is used max temperature on the pins are specified to 215°C for 10 seconds. Maximum preheat rate of 4°C/s ...
Page 18
Product Program V /I max Output 1 48/60 2.5 V/30 A 48/60 3.3 V/25 A 48/60 5 V/20 A The PKJE series DC/DC converter may be ordered with different options listed in the Product Options Table. ...