MT4C1M16E5DJ-6 Micron Semiconductor Products, MT4C1M16E5DJ-6 Datasheet
![no-image](/images/no-image-200.jpg)
MT4C1M16E5DJ-6
Available stocks
Related parts for MT4C1M16E5DJ-6
MT4C1M16E5DJ-6 Summary of contents
Page 1
... MEG x 16 EDO DRAM PART NUMBERS TG PART NUMBER -5 MT4LC1M16E5DJ-x -6 MT4LC1M16E5DJ-x S MT4LC1M16E5TG-x MT4LC1M16E5TG-x S None MT4C1M16E5DJ MT4C1M16E5TG-x None NOTE: “-x” indicates speed grade marking under timing ET options. GENERAL DESCRIPTION The 1 Meg randomly accessed, solid-state memory containing 16,777,216 bits organized in a x16 configuration ...
Page 2
GENERAL DESCRIPTION (continued) of the two signals results in a BYTE WRITE cycle. CASL# transitioning LOW selects an access cycle for the lower byte (DQ0-DQ7), and CASH# transitioning LOW se- lects an access cycle for the upper byte (DQ8-DQ15). Each ...
Page 3
PAGE ACCESS Page operations allow faster data operations (READ, WRITE or READ-MODIFY-WRITE) within a row- address-defined page boundary. The page cycle is al- ways initiated with a row address strobed in by RAS#, followed by a column address strobed in ...
Page 4
However, an EARLY WRITE on one byte and a LATE WRITE on the other byte, after a CAS# precharge has been satisfied, are permissible. DRAM REFRESH Preserve correct memory cell data by maintaining power and executing any RAS# cycle (READ, ...
Page 5
WE# CASL# CAS# CASH# NO. 2 CLOCK GENERATOR COLUMN- ADDRESS 10 BUFFER A0 REFRESH A1 CONTROLLER REFRESH A5 COUNTER ROW- A9 ADDRESS 10 BUFFERS (10) NO. 1 CLOCK RAS# GENERATOR 1 Meg x ...
Page 6
ABSOLUTE MAXIMUM RATINGS* Voltage on V Pin Relative 3.3V ......................................................... -1V to +4.6V 5V ............................................................... -1V to +7V Voltage on NC, Inputs or I/O Pins Relative to Vss: 3.3V ......................................................... -1V to +5.5V 5V ............................................................... -1V ...
Page 7
I OPERATING CONDITIONS AND MAXIMUM LIMITS CC (Notes notes appear on pages 10-11); (V PARAMETER/CONDITION STANDBY CURRENT: TTL (RAS# = CAS STANDBY CURRENT: CMOS (non-“S” version only) (RAS# = CAS# = ...
Page 8
CAPACITANCE (Notes notes appear on pages 10-11) PARAMETER Input Capacitance: Addresses Input Capacitance: RAS#, CASL#,CASH#, WE#, OE# Input/Output Capacitance ELECTRICAL CHARACTERISTICS (Notes 10, 11, 12; notes appear on pages 10-11); ...
Page 9
AC ELECTRICAL CHARACTERISTICS (continued) (Notes 10, 11, 12; notes appear on pages 10-11 CHARACTERISTICS PARAMETER OE# setup prior to RAS# during HIDDEN REFRESH cycle EDO-PAGE-MODE READ or WRITE cycle time EDO-PAGE-MODE READ-WRITE cycle time Access ...
Page 10
NOTES 1. All voltages referenced The minimum specifications are used only to indicate cycle time at which proper operation over the full temperature range (0ºC commercial) and (-20º ensured initial pause ...
Page 11
NOTES (continued) 26.Each CAS#x must meet minimum pulse width. 27.The last CAS#x edge to transition HIGH. 28.Last falling CAS#x edge to first rising CAS#x edge. 29.Last rising CAS#x edge to first falling CAS#x edge. 30.Last rising CAS#x edge to next ...
Page 12
V IH RAS CRP V IH CASL#/CASH ASR V IH ADDR WE OE TIMING PARAMETERS -5 SYMBOL MIN MAX ...
Page 13
V IH RAS CRP CASL#/CASH ASR V IH ADDR ROW IOH DQ V IOL TIMING PARAMETERS -5 SYMBOL MIN ...
Page 14
WRITE and READ-MODIFY-WRITE cycles RAS CRP V IH CASL#/CASH ASR V IH ADDR ROW WE IOH DQ V IOL ...
Page 15
V IH RAS CSH t CRP V CASL#/CASH RAD t RAD t ASR t RAH V IH ADDR V ROW OPEN ...
Page 16
V IH RAS CSH t CRP V IH CASL#/CASH RAD t ASR t RAH V IH ADDR V ROW WE IOH DQ V IOL V IH OE# V ...
Page 17
WRITE and READ-MODIFY-WRITE cycles RAS CRP CASL#/CASH RAD t ASR t RAH V IH ADDR ROW IOH DQ V ...
Page 18
EDO-PAGE-MODE READ EARLY WRITE CYCLE V IH RAS CRP V IH CASL#/CASH RAD t ASR t RAH V IH ADDR ROW WE IOH DQ OPEN V IOL ...
Page 19
V IH RAS CRP V IH CASL#/CASH ASR V IH ADDR WE OE TIMING PARAMETERS -5 SYMBOL MIN MAX ...
Page 20
V IH RAS CRP V IH CASL#/CASH ASR V IH ADDR RAS RPC CASL#/CASH ...
Page 21
V IH RAS CRP V IH CASL#/CASH ASR t RAH V IH ADDR ROW IOH DQx V IOL TIMING PARAMETERS -5 SYMBOL MIN MAX t AA ...
Page 22
RAS RPC CSR V IH CASL CASH WRP TIMING PARAMETERS -5 SYMBOL MIN MAX t CHD 15 ...
Page 23
PIN #1 INDEX .031 (0.80) TYP NOTE: 1. All dimensions in inches (millimeters) MAX or typical where noted. 2. Package width and length do not include mold protrusion; allowable mold protrusion is .01" per ...
Page 24
PIN #1 INDEX SEATING PLANE NOTE: 1. All dimensions in inches (millimeters) MAX or typical where noted. 2. Package width and length do not include mold protrusion; allowable mold protrusion is .01" ...