MT4LC1M16C3DJ-5 Micron Semiconductor Products, MT4LC1M16C3DJ-5 Datasheet
MT4LC1M16C3DJ-5
Related parts for MT4LC1M16C3DJ-5
MT4LC1M16C3DJ-5 Summary of contents
Page 1
... Operating Temperature Range o o Commercial ( + Extended (- +80 C) Part Number Example: MT4LC1M16C3DJ-5 NOTE: 1. The third field distinguishes the low voltage offering: LC designates V = 3.3V and C designates Contact factory for availability. 3. Available only on MT4C1M16C3 (5V) KEY TIMING PARAMETERS SPEED ...
Page 2
GENERAL DESCRIPTION (continued) the last CAS# to transition back HIGH. Use of only one of the two results in a BYTE access cycle. CASL# transitioning LOW selects an access cycle for the lower byte (DQ0-DQ7), and CASH# transitioning LOW se- ...
Page 3
FAST PAGE MODE ACCESS (continued) The MT4LC1M16C3 must be refreshed periodically in order to retain stored data. FAST PAGE MODE ACCESS FAST-PAGE-MODE operations allow faster data op- erations (READ, WRITE or READ-MODIFY-WRITE) within a row-address-defined (A0-A9) page boundary. The FAST-PAGE-MODE ...
Page 4
Additionally, both bytes must always be of the same mode of operation if both bytes are active. A CAS# precharge must be satisfied prior to changing modes of operation between the upper and lower bytes. For ex- ample, an EARLY ...
Page 5
ABSOLUTE MAXIMUM RATINGS* Voltage on V Pin Relative 3.3V ..................................................... -1V to +4.6V 5V ........................................................... -1V Voltage on NC, Inputs or I/O Pins Relative to V 3.3V ..................................................... -1V to +5.5V 5V ........................................................... -1V Operating Temperature T ...
Page 6
I OPERATING CONDITIONS AND MAXIMUM LIMITS CC (Notes notes can be found on page 9); V PARAMETER/CONDITION STANDBY CURRENT: TTL (RAS# = CAS STANDBY CURRENT: CMOS (non-“S” version only) (RAS# = ...
Page 7
AC ELECTRICAL CHARACTERISTICS (Notes 10, 11, 12; notes can be found on page 9 CHARACTERISTICS PARAMETER Access time from column address Column-address hold time (referenced to RAS#) Column-address setup time Row-address setup time ...
Page 8
AC ELECTRICAL CHARACTERISTICS (Notes 10, 11, 12; notes can be found on page 9 CHARACTERISTICS PARAMETER RAS# to WE# delay time WRITE command to RAS# lead time Transition time (rise or fall) WRITE ...
Page 9
NOTES 1. All voltages referenced This parameter is sampled MHz dependent on output loading. Specified CC values are obtained with minimum cycle time and the output open. 4. Enables ...
Page 10
NOTES (continued) 32. Last rising CASx edge to first falling CASx edge. 33. First DQs controlled by the first CASx to go LOW. 34. Last DQs controlled by the last CASx to go HIGH. 35. Each CASx must meet minimum ...
Page 11
V IH RAS CRP CASL#/CASH ASR V IH ROW ADDR IOH DQ V IOL TIMING PARAMETERS -5 SYMBOL MIN ...
Page 12
V IH RAS CRP CASL#/CASH ASR V IH ADDR ROW IOH DQ V IOL TIMING PARAMETERS -5 SYMBOL MIN ...
Page 13
WRITE and READ-MODIFY-WRITE cycles RAS CRP CASL#/CASH ASR V IH ADDR ROW WE IOH DQ V IOL ...
Page 14
V IH RAS CSH t CRP V CASL#/CASH RAD t ASR t RAH V IH ADDR V ROW IL WE IOH DQ OPEN V IOL V IH OE# ...
Page 15
FAST-PAGE-MODE EARLY WRITE CYCLE V IH RAS CSH t CRP V CASL#/CASH RAD t ASR t RAH V IH ADDR ROW IOH DQ V IOL ...
Page 16
WRITE and READ-MODIFY-WRITE cycles RAS CRP CASL#/CASH RAD t ASR t RAH V IH ADDR ROW IOH DQ V ...
Page 17
FAST-PAGE-MODE READ EARLY WRITE CYCLE V IH RAS CRP V IH CASL#/CASH ASR V IH ADDR V ROW WE OE ...
Page 18
V IH RAS CRP V IH CASL#/CASH ASR V IH ADDR RAS RPC CSR V IH CASL#/CASH# ...
Page 19
TIMING PARAMETERS -5 SYMBOL MIN MAX MIN ASC 0 t ASR 0 t CAC 15 t CAH 8 t CHR 8 t CLZ 0 t CRP NOTE: 1. ...
Page 20
RAS RPC CSR V IH CAS WRP TIMING PARAMETERS -5 SYMBOL MIN MAX MIN t CHD 15 ...
Page 21
PIN #1 INDEX SEATING PLANE 1. All dimensions in inches (millimeters) MAX or typical where noted. NOTE: 2. Package width and length do not include mold protrusion; allowable mold protrusion is .01" ...
Page 22
PIN #1 INDEX .031 (0.80) TYP 1. All dimensions in inches (millimeters) MAX or typical where noted. NOTE: 2. Package width and length do not include mold protrusion; allowable mold protrusion is .01" per ...