LT6205CS5#TRM Linear Technology, LT6205CS5#TRM Datasheet - Page 6
![IC OPAMP VID SGL 100MHZ TSOT23-5](/photos/6/57/65785/tsot-23-5_05-08-1635_sml.jpg)
LT6205CS5#TRM
Manufacturer Part Number
LT6205CS5#TRM
Description
IC OPAMP VID SGL 100MHZ TSOT23-5
Manufacturer
Linear Technology
Datasheet
1.LT6205CS5TRM.pdf
(18 pages)
Specifications of LT6205CS5#TRM
Applications
Voltage Feedback
Output Type
Rail-to-Rail
Number Of Circuits
1
Slew Rate
600 V/µs
Current - Supply
4mA
Current - Output / Channel
60mA
Voltage - Supply, Single/dual (±)
2.7 V ~ 12.6 V, ±1.35 V ~ 6.3 V
Mounting Type
Surface Mount
Package / Case
SOT-23-5 Thin, TSOT-23-5
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
LT6205CS5
LT6205CS5
LT6205CS5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
ELECTRICAL CHARACTERISTICS
SYMBOL
I
I
e
i
CMRR
PSRR
A
I
I
GBW
SR
FPBW
t
LT6205/LT6206/LT6207
temperature range, –40°C ≤ T
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The inputs are protected by back-to-back diodes. If the differential
input voltage exceeds 1.4V, the input current should be limited to less than
10mA.
Note 3: A heat sink may be required to keep the junction temperature
below absolute maximum. This depends on the power supply voltage and
how many amplifi ers are shorted.
Note 4: The LT6205C/LT6206C/LT6207C are guaranteed to meet specifi ed
performance from 0°C to 70°C and are designed, characterized and
expected to meet specifi ed performance from –40°C to 85°C but are not
tested or QA sampled at these temperatures. The LT6205I/LT6206I/LT6207I
are guaranteed to meet specifi ed performance from –40°C to 85°C. The
LT6205H is guaranteed to meet specifi ed performance from –40°C to 125°C.
6
n
B
OS
SC
S
s
n
VOL
PARAMETER
Input Bias Current
Input Offset Current
Input Noise Voltage
Input Noise Voltage Density
Input Noise Current Density
Input Resistance
Input Capacitance
Common Mode Rejection Ratio
Input Voltage Range
Power Supply Rejection Ratio
Large-Signal Voltage Gain
Output Voltage Swing
Short-Circuit Current
Supply Current per Amplifi er
Gain Bandwidth Product
Slew Rate
Channel Separation
Full Power Bandwidth
Settling Time to 3%
Settling Time to 1%
Differential Gain
Differential Phase
A
≤ 125°C, otherwise specifi cations are at T
CONDITIONS
0.1Hz to 10Hz
f = 10kHz
f = 10kHz
V
V
V
V
V
No Load, Input Overdrive = 30mV
I
I
Short to Ground
f = 2MHz
A
V
f = 10MHz
V
ΔV
A
A
OUT
OUT
CM
CM
S
O
O
O
OUT
V
V
V
OUT
= ±2V to ±6V
= –1, R
= 2, R
= 2, R
= –4V to 4V, R
= –3V to 3V, R
= –4V to 4V, Measured from –3V to 3V
= –5V to 3V
= –5V to 3V
= ±5mA
= ±25mA
= 8V
= 2V, A
L
L
P-P
L
= 150Ω, Output Black Level = 1V
= 150Ω, Output Black Level = 1V
= 1k
(Note 8)
V
The
= –1, R
L
L
= 1k
= 150Ω
l
denotes specifi cations which apply over the full specifi ed
L
= 150Ω
Note 5: Matching parameters are the difference between the two amplifi ers
A and D and between B and C of the LT6207; between the two amplifi ers of
the LT6206.
Note 6: This parameter is not 100% tested.
Note 7: Output voltage swings are measured between the output and
power supply rails.
Note 8: Full power bandwidth is calculated from the slew rate
measurement: FPBW = SR/2πV
Note 9: There are reverse biased ESD diodes on all inputs and outputs.
If these pins are forced beyond either supply, unlimited current will fl ow
through these diodes. If the current is transient in nature and limited to
less than 25mA, no damage to the device will occur.
A
= 25°C. V
S
= ±5V; V
CM
l
l
l
l
l
l
l
l
l
l
l
l
l
PEAK
= V
OUT
±4.85
±4.65
.
MIN
±3.5
±40
±20
350
72
–5
62
40
50
14
5
= 0V, unless otherwise noted.
LT6205H
0.05
0.08
TYP
±60
600
90
24
15
25
2
9
4
1
2
4
MAX
5.6
7.5
50
5
3
pA/√Hz
nV/√Hz
620567fc
UNITS
μV
V/mV
V/mV
MHz
V/μs
MHz
MΩ
Deg
mA
mA
mA
mA
P-P
μA
μA
dB
dB
dB
pF
ns
ns
%
V
V
V
V