HA3-5033-5 Intersil, HA3-5033-5 Datasheet - Page 3

• Manufacturer Part Number: HA3-5033-5
• Description: IC VIDEO BUFFER 250MHZ 8-PDIP
• Manufacturer: Intersil
• Type: High Output, High Slew Rater

Specifications of HA3-5033-5

• Applications: Buffer
• Number Of Circuits: 1
• -3db Bandwidth: 250MHz
• Slew Rate: 1100 V/µs
• Current - Supply: 21mA
• Current - Output / Channel: 100mA
• Voltage - Supply, Single/dual (±): ±5 V ~ 16 V
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• Amplifier Type: Video Buffer
• Bandwidth: 250 MHz
• Current, Input Bias: 20 μA
• Current, Output: ±100 mA
• Current, Supply: 21 mA
• Harmonic Distortion: 0.1 %
• Impedance, Thermal: 120 °C/W
• Number Of Amplifiers: Single
• Package Type: PDIP-8
• Propagation Delay: 1 ns
• Resistance, Input: 3 Megohms
• Temperature, Operating, Range: 0 to +75 °C
• Time, Rise: 4.6 ns
• Voltage, Gain: 0.99 V/V
• Voltage, Input Offset: 5 mV
• Voltage, Noise: 20 μVp-p
• Voltage, Output Swing: ±10 V
• Voltage, Supply: ±12 V
• No. Of Amplifiers: 1
• Gain Bandwidth: 250MHz
• Supply Voltage Range: ± 5V To ± 16V
• Output Current: 100mA
• Amplifier Output: Single Ended
• Rohs Compliant: No
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Electrical Specifications
NOTES:
Test Circuits and Waveforms
Overshoot
Slew Rate (Note 4)
Settling Time to 0.1%
Differential Phase Error (Note 5)
Differential Gain Error (Note 5)
POWER SUPPLY CHARACTERISTICS
Supply Current
Power Supply Rejection Ratio
Harmonic Distortion
4. V
5. Differential gain and phase error are nonlinear signal distortions found in video systems and are defined as follows: Differential gain error is
defined as the change in amplitude at the color subcarrier frequency as the picture signal is varied from blanking to white level. Differential phase
error is defined as the change in the phase of the color subcarrier as the picture signal is varied from blanking to white level. R
SUPPLY
OUTPUT
FIGURE 1. SLEW RATE AND SETTLING TIME
FIGURE 3. SETTLING TIME AND SLEW RATE
PARAMETER
IN
INPUT
0V
= ±15V, V
10V
90%
10%
+15V
-15V
OUT
SETTLING TIME
∆t
0.1µF
0.1µF
= ±10V, R
SLEW
RATE =
∆V/∆t
3
∆V
V
V
SUPPLY
IN
L
= 1V
= 1kΩ.
CONDITIONS
R
RMS
ERROR BAND
±10mV FROM
FINAL VALUE
= ±12V, R
L
TEST
at 100kHz
OUT
S
= 50Ω, R
HA-5033
L
TEMP.
= 100Ω, C
(°C)
Full
Full
25
25
25
25
25
25
25
MIN
L
54
1
-
-
-
-
-
-
-
= 10pF, Unless Otherwise Specified (Continued)
OUTPUT
HA-5033-2
90%
10%
INPUT
TYP
0.02
0.03
<0.1
1.1
50
21
21
0V
IN
FIGURE 4. RISE TIME AND OVERSHOOT
3
-
500mV
FIGURE 2. TRANSIENT RESPONSE
MAX
OVERSHOOT
25
30
-
-
-
-
-
-
-
+12V
NOTE: Measured on both
positive and negative transitions.
-12V
0.1µF
0.1µF
MIN
54
1
-
-
-
-
-
-
-
HA-5033-5
TYP
0.02
0.03
<0.1
1.1
50
21
21
3
-
100Ω
MAX
25
30
L
OUT
-
-
-
-
-
-
-
= 300Ω.
Degree
UNITS
FN2924.8
V/ns
mA
mA
dB
ns
%
%
%