FE200F98 Lucent Technologies, FE200F98 Datasheet
FE200F98
Available stocks
Related parts for FE200F98
FE200F98 Summary of contents
Page 1
January 1999 dc-dc Converter; 38 Vdc to 60 Vdc Input, 3.3 Vdc Output; 132 W The FE200F9 Power Module uses advanced, surface-mount technology and delivers high-quality, compact, dc-dc conversion at an economical price. Applications Redundant and distributed power architectures Telecommunications ...
Page 2
... C T –55 stg Symbol Min Typ — — I, max — — — — 35 — — 60 Data Sheet January 1999 Max Unit 60 Vdc 500 V 80 °C 125 °C Max Unit 60 Vdc 1 — mAp-p — dB Lucent Technologies Inc. ...
Page 3
... Load Change from I = 50 Peak Deviation Settling Time (V < 10% of peak deviation) O Load Change from I = 50 Peak Deviation Settling Time (V < 10% of peak deviation) O Lucent Technologies Inc. (continued) Symbol set V O, set — — — — — ...
Page 4
... Lucent Technologies Inc. Unit pF M Unit hours g (oz.) Unit µ nom % I O, max %V O, nom °C ...
Page 5
... Figure 1. Typical FE200F9 Input Characteristics at Room Temperature 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 OUTPUT CURRENT, I Figure 2. Typical FE200F9 Output Characteristics at Room Temperature Lucent Technologies Inc. dc-dc Converter; 38 Vdc to 60 Vdc Input, 3.3 Vdc Output; 132 W 82 FULL LOAD MID LOAD 74 72 LIGHT LOAD (V) ...
Page 6
... Full Load at Room Temperature and 48 V Input (Waveform Averaged to Eliminate Ripple Component 30,670 µF 27,270 µF 22,500 µF NO CAP 8-1622 (C) Figure 7. Typical FE200F9 Start-Up Transient at Room Temperature Input, and Full Load Output 8-1623 (C) Data Sheet January 1999 8-1624 (C).a Lucent Technologies Inc. ...
Page 7
... Note: Use a 0.1 µF ceramic capacitor. Scope measurement should be made using a BNC socket. Position the load between in.) and in.) from the module. Figure 10. Peak-to-Peak Output Noise Measurement Test Setup Lucent Technologies Inc. Design Considerations Input Source Impedance The power module should be connected to a low CURRENT ac-impedance input source ...
Page 8
... SENSE(–) V (+) V (+) LOAD (–) V (– CONTACT AND DISTRIBUTION LOSSES Single-Module Remote-Sense Operation ) between the trim-up ) increases the output O, adj 1.25 3. ----------------------------- - V 3.3 – O adj , ) between trim-down ) decreases the O adj , V 1.25 3.32 – O, adj = ------------------------------------------------------- - k 3.3 V – O, adj Lucent Technologies Inc. 0.5 V (+) and O 8-651 (C) ...
Page 9
... The equation below shows the resistance required to obtain the desired output voltage – 807 adj O, adj O, nom Lucent Technologies Inc. SUPPLY (–) terminals O CONTACT RESISTANCE Figure 15. Circuit Configuration to Adjust Output R trim-up Forced Load Sharing (Parallel Operation) For either redundant operation or additional power requirements, the power modules can be confi ...
Page 10
... This filtered sig- nal is used to determine if a module operating in paral- lel with other modules is delivering current has failed. This signal is useful only when modules operate in parallel. Specific application questions can be directed to your Lucent Technologies Microelectronics Group Application Engineer Overtemperature Shutdown To provide protection in fault condition, the unit is equipped with an overtemperature shutdown circuit ...
Page 11
... The location to measure case temperature (T shown in Figure 17. Case-to-ambient thermal resis- tance vs. airflow for various heat sink configurations is shown in Figure 19 and Figure 20. These curves were obtained by experimental testing of heat sinks, which are offered in the product catalog. Lucent Technologies Inc. (continued) 5.0 4.0 3.0 2.0 1 ...
Page 12
... This equation provides a conservative estimate for such instances. Layout Considerations Copper paths must not be routed beneath the power module standoffs. Data Sheet January 1999 to-Ambient T – – ------------------------ - P D Lucent Technologies Inc 8-1304 (C) ...
Page 13
... TYP 13 PLCS Bottom View 4.3 (0.17) 5.08 (0.200) 10.16 (0.400) 15.24 (0.600) Lucent Technologies Inc. 121.9 (4.80) FE200F98 DC-DC Power Module IN:DC 48V, 3.5A OUT:DC 3.3V, 40A 132W MADE IN USA TUV Rheinland Protected by U.S. Patents: 5,036,452 5,179,365 55.63 (2.190) 55.63 (2.190) FOR OPTIONAL HEAT SINK MOUNTING #4-40 THD 4.6 (0.18) DEEP 6 PLCS 0.05 (0.002) DIA 113.54 (4.470) ...
Page 14
... OUT + (0.48) 113.43 (4.470) Power Output Good Trim Power Signal 132 W No Yes 132 W Yes Yes Data Sheet January 1999 POWER GOOD SIGNAL OPTION ONLY 40.64 35.56 (1.600) 30.48 (1.400) 25.40 (1.200) 20.32 (1.000) (0.800) 12.2 Device Comcode Code FE200F9 106899735 FE200F98 107252124 Lucent Technologies Inc. 8-1617 (C) ...
Page 15
... Data Sheet dc-dc Converter; 38 Vdc to 60 Vdc Input, 3.3 Vdc Output; 132 W January 1999 Notes Lucent Technologies Inc. 15 ...
Page 16
... ITALY: (39) 02 6608131 (Milan), SPAIN: (34) 91 807 1441 (Madrid) Lucent Technologies Inc. reserves the right to make changes to the product(s) or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. ...