AD8023AR-REEL7 Analog Devices Inc, AD8023AR-REEL7 Datasheet - Page 10
![IC AMP VIDEO TRIPLE HC 14-SOIC](/photos/5/67/56705/505-14-soic_sml.jpg)
AD8023AR-REEL7
Manufacturer Part Number
AD8023AR-REEL7
Description
IC AMP VIDEO TRIPLE HC 14-SOIC
Manufacturer
Analog Devices Inc
Datasheet
1.AD8023ARZ.pdf
(11 pages)
Specifications of AD8023AR-REEL7
Rohs Status
RoHS non-compliant
Applications
Current Feedback
Number Of Circuits
3
-3db Bandwidth
125MHz
Slew Rate
1200 V/µs
Current - Supply
7mA
Current - Output / Channel
70mA
Voltage - Supply, Single/dual (±)
4.2 V ~ 15 V, ±2.1 V ~ 7.5 V
Mounting Type
Surface Mount
Package / Case
14-SOIC (0.154", 3.90mm Width)
AD8023
Overload Recovery
The three important overload conditions are: input common-
mode voltage overdrive, output voltage overdrive, and input
current overdrive. When configured for a low closed-loop gain,
this amplifier will quickly recover from an input common-mode
voltage overdrive; typically in under 25 ns. When configured for
a higher gain, and overloaded at the output, the recovery time
will also be short. For example, in a gain of +10, with 50%
overdrive, the recovery time of the AD8023 is about 20 ns (see
Figure 31). For higher overdrive, the response is somewhat
slower. For 100% overdrive, (in a gain of +10), the recovery
time is about 80 ns.
C
20
50
100
200
300
≥500
Figure 32. Pulse Response Driving a Large Load Capacitor.
C
Table II. Recommended Feedback and Series Resistors vs.
Capacitive Load and Gain
L
L
– pF
= 300 pF, G = +3, R
Figure 31. Circuit for Driving a Capacitive Load
V
V
IN
V
O
IN
R
G
2k
2k
2k
3k
3k
3k
R
R
F
T
– Ohms
R
F
AD8023
F
= 750 Ω , R
+V
–V
11
4
S
S
0.1 F
0.1 F
1.0 F
1.0 F
S
= 16.9 Ω , R
G = 2
0
10
15
10
10
10
R
15
S
R
– Ohms
S
L
= 10 k Ω
C
L
G ≥ 3
0
10
15
10
10
10
V
O
–10–
As noted in the warning under Maximum Power Dissipation, a
high level of input overdrive in a high noninverting gain circuit
can result in a large current flow in the input stage. Though this
current is internally limited to about 30 mA, its effect on the
total power dissipation may be significant.
Disable Mode Operation
Pulling the voltage on any one of the Disable pins about 1.6 V up
from the negative supply will put the corresponding amplifier
into a disabled, powered down, state. In this condition, the
amplifier’s quiescent current drops to about 1.3 mA, its output
becomes a high impedance, and there is a high level of isolation
from input to output. In the case of a gain of two line driver for
example, the impedance at the output node will be about the
same as for a 1.5 kΩ resistor (the feedback plus gain resistors)
in parallel with a 12 pF capacitor.
Leaving the Disable pin disconnected (floating) will leave the
corresponding amplifier operational, in the enabled state. The
input impedance of the disable pin is about 25 kΩ in parallel
with a few picofarads. When driven to 0 V, with the negative
supply at –7.5 V, about 100 µA flows into the disable pin.
When the disable pins are driven by complementary output
CMOS logic, on a single 5 V supply, the disable and enable
times are about 50 ns. When operated on dual supplies, level
shifting will be required from standard logic outputs to the
Disable pins. Figure 33 shows one possible method, which
results in a negligible increase in switching time.
The AD8023’s input stages include protection from the large
differential input voltages that may be applied when disabled.
Internal clamps limit this voltage to about ±3 V. The high input to
output isolation will be maintained for voltages below this limit.
Figure 34. Level Shifting to Drive Disable Pins on Dual
Supplies
Figure 33. 50% Overload Recovery, Gain = +10,
(R
F
V
V
= 300 Ω , R
IN
O
V
I
V
V
L
I
I
HIGH => AMPLIFIER ENABLED
LOW => AMPLIFIER DISABLED
= 1 k Ω , V
+5
15k
4k
S
10k
= ± 7.5 V)
+7.5V
–7.5V
TO DISABLE PIN
REV. A