AD9869 Analog Devices, AD9869 Datasheet
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AD9869
Specifications of AD9869
Related parts for AD9869
AD9869 Summary of contents
Page 1
... MSPS span. Both the RxPGA and the ADC offer scalable power consumption allowing power/performance optimization. The AD9869 provides a highly integrated solution for many broadband modems available in a space-saving package, a 16-lead LFCSP, and is specified over the commercial temperature range (−40°C to +85°C). ...
Page 2
... AD9869 TABLE OF CONTENTS Features .............................................................................................. 1 Applications....................................................................................... 1 Functional Block Diagram .............................................................. 1 General Description ......................................................................... 1 Revision History ............................................................................... 2 Specifications..................................................................................... 3 Tx Path Specifications.................................................................. 3 Rx Path Specifications.................................................................. 4 Power Supply Specifications........................................................ 6 Digital Specifications ................................................................... 7 Serial Port Timing Specifications ............................................... 7 Half-Duplex Data Interface (ADIO Port) Timing Specifications ................................................................................ 8 Full-Duplex Data Interface (Tx and Rx Port) Timing Specifications ...
Page 3
... Monotonic ±2 0.5 66.6 69.2 68.4 69.8 −79 −68.7 68 105 1 3.9 13 43.3 45.2 1.23 0.7 3 0.2187 0.2405 50 96 0.1095 0.1202 50 AD9869 Unit Bits MSPS μ dBm dBc dBc dBc dBc mA V dBm dBc ppm/ C Cycles f /f OUT DAC f /f OUT DAC ...
Page 4
... AD9869 Parameter PLL CLK MULTIPLIER OSCIN Frequency Range PLL M Factor Set to 2 PLL M Factor Set to 4 PLL M Factor Set to 8 Internal VCO Frequency Range Duty Cycle OSCIN Impedance 6 CLKOUT1 Jitter CLKOUT2 Jitter 7 8 CLKOUT1 and CLKOUT2 Duty Cycle 1 See the Explanation of Test Levels section. ...
Page 5
... Full MSPS ADC 25°C 25°C 25°C 25°C Full Full MSPS ADC 25°C 25°C 25°C 25°C 25°C 25°C 25°C 25°C . ADC Rev Page AD9869 1 Test Level Min Typ Max V 10.5 V 10.0 III 43.7 III −71 III 63.1 III −67.2 IV 64.3 IV −67.3 III 41.8 III − ...
Page 6
... AD9869 POWER SUPPLY SPECIFICATIONS AVDD = 3.3 V, DVDD = CLKVDD = DRVDD = 3 Table 3. Parameter SUPPLY VOLTAGES AVDD CLKVDD DVDD DRVDD IS_TOTAL (Total Supply Current) POWER CONSUMPTION (Analog Supply Current) AVDD CLKVDD (Digital Supply Current) DVDD DRVDD POWER CONSUMPTION (Half-Duplex Operation with f Tx Mode ...
Page 7
... DRVDD − 0.7 0 DRVDD − 0.7 0.4 1.5/2.3 1.9/2.7 0.7/0.7 1.0/1 Test Level Min Typ AD9869 Unit V V μ Clock cycles Max Unit 32 MHz MHz ...
Page 8
... AD9869 HALF-DUPLEX DATA INTERFACE (ADIO PORT) TIMING SPECIFICATIONS AVDD = 3.3 V ± 5%, DVDD = CLKVDD = DRVDD = 3.3 V ± 10%, unless otherwise noted. Table 6. Parameter READ OPERATION 2 (See Figure 9) Output Data Rate Three-State Output Enable Time (t ) PZL Three-State Output Disable Time (t ) PLZ Rx Data Valid Time ( Data Output Delay (t ...
Page 9
... IV. Parameter is guaranteed by design and characterization testing. 125°C −65°C to +150°C V. Parameter is a typical value only. VI. 100% production tested at 25°C and guaranteed by design and characterization for industrial temperature range. ESD CAUTION Rev Page AD9869 ...
Page 10
... ADIO1 Rx[1] 12 ADIO0 Rx[0] 13 RXEN RXSYNC 14 TXEN TXSYNC PIN 1 3 IDENTIFIER AD9869 7 TOP VIEW 8 (Not to Scale Figure 2. Pin Configuration 1 Mode Description HD MSB of ADIO Buffer. FD MSB of Tx Nibble Input. ...
Page 11
... Power-Up SPI Register Default Setting Input. Clock Oscillator/Synthesizer Supply Return. Crystal Oscillator Inverter Output. Crystal Oscillator Inverter Input. Clock Oscillator/Synthesizer Supply. Digital Supply Return. Digital Supply Input Clock Output ( 4). OSCIN Power-Down Input. The exposed pad must be soldered to ground. Rev Page AD9869 . ADC ...
Page 12
... AD9869 SERIAL PORT Table 10. SPI Register Mapping Address 1 (Hex) Bit Description SPI PORT CONFIGURATION AND SOFTWARE RESET 0x00 7 4-Wire SPI 6 SPI LSB First 5 Software Reset POWER CONTROL REGISTERS (Via PWRDWN Pin) 0x01 7 CLK Synthesizer 6 TxDAC/IAMP 5 Tx Digital 4 REF 3 ADC CML 2 ADC ...
Page 13
... ADC Rx data fed back to TxDAC. Digital loopback: Tx input data to Rx output port. Default setting is for high drive strength and IAMP enabled Standing current. Current bias setting for Rx path’s functional blocks. Refer to the Power Reduction Options section. AD9869 ...
Page 14
... The CONFIG pin can be used to select the default interpolation ratio of the Tx path and RxPGA gain mapping. SERIAL PORT INTERFACE (SPI) The serial port of the AD9869 has 3-wire or 4-wire SPI capability allowing read/write access to all registers that configure the device’s internal parameters. Registers pertaining to the SPI are listed in Table 11 ...
Page 15
... R/W Figure 6. SPI 3-Wire Read Operation Timing SCLK t t LOW R Figure 7. SPI 4-Wire Read Operation Timing Rev Page AD9869 ...
Page 16
... TX3 TX4 master to the digital ASIC. An example of a slave configuration is shown in Figure 10. In this example, the AD9869 accepts all the clock and control signals from the digital ASIC. Because the sampling clocks for the DAC and ADC are derived internally from the OSCIN signal, the TXCLK and RXCLK signals must be at exactly the same frequency as the OSCIN signal ...
Page 17
... A buffered version of the signal appearing at OSCIN can also be directed to RXCLK by setting Bit 2 of Register 0x05. This feature allows the AD9869 to be completely powered down (including the clock synthesizer) while serving as the master. ...
Page 18
... The output driver strength can also be reduced for lower data rate applications. For the AD9869, the most significant nibble defaults to 6 bits, and the least significant nibble defaults to 4 bits. This can be changed so that the least significant nibble and most significant nibble have 5 bits each ...
Page 19
... RxPGA CONTROL The AD9869 contains a digital PGA in the Rx path that is used to extend the dynamic range. The RxPGA can be programmed over − +48 dB with 1 dB resolution using a 6-bit word, and with setting corresponding p-p input signal. The 6-bit word is fed into a look-up table (LUT) that is used to distribute the desired gain over three amplification stages within the Rx path ...
Page 20
... AD9869 TxPGA CONTROL The AD9869 also contains a digital PGA in the Tx path distri- buted between the TxDAC and IAMP. The TxPGA is used to control the peak current from the TxDAC and IAMP over a 7.5 dB and 19.5 dB span, respectively, with 0.5 dB resolution. A 6-bit word is used to set the TxPGA attenuation according to the mapping shown in Figure 17 ...
Page 21
... TxDAC, and a current-output amplifier, IAMP (see Figure 18). Note that the additional two bits of resolution offered by the AD9869 result reduction in the pass- band noise floor. The digital interpolation filter relaxes the Tx analog filtering requirements by simultaneously reducing the images from the DAC reconstruction process while increasing the analog filter’ ...
Page 22
... AD9869 TxDAC AND IAMP ARCHITECTURE The Tx path contains a TxDAC with a current amplifier, IAMP. The TxDAC reconstructs the output of the interpolation filter and sources a differential current output that can be directed to an external load or fed into the IAMP for further amplification. The TxDAC and IAMP peak current outputs are digitally programmable over − ...
Page 23
... IOUTN– –7.5dB 0 TO –12dB IOUT = N × POUT PK Figure 23. Current-Mode Operation BIAS . Note that the V bias should not exceed 3.3 V. The × N × I × V IAMP CM AD9869 to 0 − AVDD × N × I BIAS T (IOUT ) × T × ...
Page 24
... AD9869 RECEIVE PATH The receive signal path for the AD9869 (or its related part, the AD9868) consists of a 3-stage RxPGA, a 3-pole programmable LPF, and a 12-bit (or 10-bit) ADC (see Figure 24). Note that the additional two bits of resolution offered by the AD9869 result lower noise floor, depending on the RxPGA gain setting and LPF cutoff frequency ...
Page 25
... INPUT FREQUENCY (MHz) Figure 28. Effects of RxPGA Gain on LPF Frequency Response ( MHz @ 0 dB and MSPS) −3 dB ADC 1 can be used to estimate (128/target) × (f /80) ×(f /30 + 23.83) f −3dB_0dB ADC ADC range of 15 MHz to 35 MHz and an f −3 dB AD9869 1.30 1.25 1.20 1.15 1.10 1.05 1.00 0.95 0.90 0.85 0.80 0.75 0.70 0.65 0.8 0.9 1.0 varies as a –6dB GAIN ...
Page 26
... MSPS and RxPGA = 0 dB −3 dB ADC ANALOG-TO-DIGITAL CONVERTER (ADC) The AD9869 features a 12-bit analog-to-digital converter (ADC) capable MSPS. As shown in Figure 24, the ADC is driven by the SPGA stage, which performs both the sample-and-hold and the fine gain adjust functions. A buffer amplifier (not shown) isolates the last CPGA gain stage from the dynamic load presented by the SPGA stage ...
Page 27
... An impulse response at the RxPGA input can be observed after 10.0 ADC clock cycles (1/f half-duplex interface, and 10.5 ADC clock cycles in the case of a full-duplex interface. This latency, along with the RxPGA settling time, should be considered to ensure stability of the AGC loop. Rev Page AD9869 ) in the case of a ADC ...
Page 28
... AD9869 CLOCK SYNTHESIZER The AD9869 generates all its internal sampling clocks, as well as two user-programmable clock outputs appearing at CLKOUT1 and CLKOUT2, from a single reference source (see Figure 32). The reference source can either be a fundamental frequency or an overtone quartz crystal connected between OSCIN and XTAL, with the parallel resonant load components specified by the crystal manufacturer ...
Page 29
... OSCIN, exhibiting the same duty cycle characteristics. With L set the output of CLKOUT2 is a divided version of the OSCIN signal, exhibiting a near 50% duty cycle, but without having a deterministic phase relationship relative to CLKOUT1 (or RXCLK). Rev Page AD9869 , OSCIN ...
Page 30
... With MODE = 1 and CONFIG =1, Register 0x02 default settings are with all blocks powered off, with RXCLK providing a buffered version of the signal appearing at OSCIN. This setting results in the lowest power consumption upon power- up, while still allowing AD9869 to generate the system clock via a crystal. HALF-DUPLEX POWER SAVINGS Significant power savings can be realized in applications having a half-duplex protocol, allowing only the Rx path or Tx path to be operational at one time ...
Page 31
... To disable the fast power-down of the Tx circuitry and/or Rx circuitry, set Bit 1 and/or Bit POWER REDUCTION OPTIONS The power consumption of the AD9869 can be significantly reduced from its default setting by optimizing the power consumption vs. performance of the various functional blocks in the Tx signal path and Rx signal path. On the Tx path, ...
Page 32
... AD9869 Because the CPGA processes signals in the continuous time domain, its performance vs. bias setting remains mostly independent of the sample rate. Table 25 shows how the typical current consumption seen at AVDD varies as a function of Register 0x13, Bits[7:5], while the remaining bits are maintained at their default settings of 0 ...
Page 33
... T 85°C, the maximum allowable power dissipation can be determined by the following equation: Assuming the IAMP common-mode bias voltage is operating off the same analog supply as the AD9869, the following equa- 101 tion can be used to calculate the maximum total current consumption, I ...
Page 34
... AD9869 A hardware reset ( RESET pin) or software reset (Bit 5 of Register 0x00) can be used to place the AD9869 into a known state of operation as determined by the state of the MODE and CONFIG pins offset calibration and filter tuning routine is also initiated upon a hardware reset, but not with a software reset ...
Page 35
... Dimensions shown in millimeters Package Description 64-Lead LFCSP_VQ 64-Lead LFCSP_VQ Rev Page PIN 1 INDICATOR 64 1 7.25 EXPOSED PAD 7.10 SQ (BOTTOM VIEW) 6. 0.25 MIN 7.50 REF FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. Package Option CP-64-3 CP-64-3 AD9869 ...
Page 36
... AD9869 NOTES ©2007–2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D06736-0-8/11(A) Rev Page ...