AD7849 Analog Devices, AD7849 Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AD7849
Manufacturer Part Number
AD7849
Description
Serial Input, 14-Bit/16-Bit DAC
Manufacturer
Analog Devices
Datasheet
1.AD7849.pdf
(20 pages)
Specifications of AD7849
Resolution (bits)
16bit
Dac Update Rate
143kSPS
Dac Settling Time
7µs
Max Pos Supply (v)
+15.75V
Single-supply
No
Dac Type
Voltage Out
Dac Input Format
Ser
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD7849
Manufacturer:
JAPAN
Quantity:
5 510
Part Number:
AD7849AR
Manufacturer:
AD
Quantity:
20 000
Part Number:
AD7849ARZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD7849BRZ
Manufacturer:
ADI
Quantity:
429
Part Number:
AD7849BRZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD7849CRZ
Manufacturer:
CYPRESS
Quantity:
5 560
Part Number:
AD7849CRZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
CIRCUIT DESCRIPTION
DIGITAL-TO-ANALOG CONVERSION
Figure 15 shows the digital-to-analog section of the AD7849. There
are three on-chip DACs, each of which has its own buffer amplifier.
DAC1 and DAC2 are 4-bit DACs. They share a 16-resistor string,
but they have their own analog multiplexers. The voltage reference
is applied to the resistor string. DAC3 is a 12-bit voltage mode
DAC with its own output stage.
The four MSBs of the 16-bit digital input code drive DAC1 and
DAC2, while the 12 LSBs control DAC3. Using DAC1 and DAC2,
the MSBs select a pair of adjacent nodes on the resistor string
and present that voltage to the positive and negative inputs of
DAC3. This DAC interpolates between these two voltages to
produce the analog output voltage.
To prevent nonmonotonicity in the DAC due to amplifier offset
voltages, DAC1 and DAC2 leap-frog along the resistor string.
For example, when switching from Segment 1 to Segment 2, DAC1
switches from the bottom of Segment 1 to the top of Segment 2
while DAC 2 remains connected to the top of Segment 1. The
code driving DAC3 is automatically complemented to compensate
for the inversion of its inputs. This means that any linearity
effects due to amplifier offset voltages remain unchanged when
switching from one segment to the next, and 16-bit monotonicity is
ensured if DAC3 is monotonic. Therefore, 12-bit resistor matching
in DAC3 guarantees overall 16-bit monotonicity. This is much
more achievable than the 16-bit matching that a conventional
R-2R structure would need.
Output Stage
The output stage of the AD7849 is shown in Figure 14. It is capable
of driving a 2 kΩ load in parallel with 200 pF. The feedback and
offset resistors allow the output stage to be configured for gains of
1 or 2. Additionally, the offset resistor can be used to shift the
output range. The AD7849 has a special feature to ensure output
stability during power-up and power-down sequences. This feature
is available for control applications where actuators must not be
allowed to move in an uncontrolled fashion.
V
V
REF–
REF+
DB15 TO DB12
DAC 1
S15
S17
S3
S1
R
R
R
R
R
R
Figure 15. Digital-to-Analog Conversion
Rev. C | Page 11 of 20
DB15 TO DB12
S14
S16
S4
S2
DAC 2
When the supply voltages are changing, the V
to 0 V via a low impedance path. To prevent the output of A3
from being shorted to 0 V during this time, Transmission Gate G1
is opened. These conditions are maintained until the power
supplies stabilize, and a valid word is written to the DAC register.
At this time, G2 opens and G1 closes. Both transmission gates
are also externally controllable via the reset in ( RSTIN ) control
input. For instance, if the RSTIN input is driven from a battery
supervisor chip, then at power-off or during a brownout, the
RSTIN input will be driven low to open G1 and closeG2. The
DAC has to be reloaded, with RSTIN high, to reenable the output.
Conversely, the on-chip voltage detector output ( RSTOUT ) is
also available to the user to control other parts of the system.
The AD7849 output buffer is configured as a track-and-hold
amplifier. Although normally tracking its input, this amplifier
isplaced in hold mode for approximately 5 μs after the leading
edge of LDAC . This short state keeps the DAC output at its
previous voltage while the
new value. therefore, any glitches that occur in the transition are
not seen at the output. In systems where
low, deglitching is not in operation.
DAC 3
A1
A2
R
OFS
R
10kΩ
ONE-SHOT
10-BIT/12-BIT
LDAC
DAC 3
10/12
10kΩ
DAC
Figure 14. Output Stage
R
G3
AD7849
CIRCUITRY
VOLTAGE
MONITOR
LOGIC
C1
OUTPUT
STAGE
is internally changing to its
RSTIN
LDAC is permanently
G1
G2
OUT
pin is clamped
AD7849
V
AGND
RSTOUT
OUT