1934338-1 TE Connectivity, 1934338-1 Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/6/654/te_connectivity_sml.jpg)
1934338-1
Manufacturer Part Number
1934338-1
Description
Manufacturer
TE Connectivity
Datasheet
1.1934219-1.pdf
(8 pages)
Specifications of 1934338-1
Connector Type
Header
Pcb Mounting Orientation
Vertical
Pcb Mount Retention
With
Termination Method To Pc Board
Through Hole - Press Fit
Pcb Mount Alignment
Without
Sealed
No
Ul File Number
E28476
Stackable
No
Data Rate (gb/s)
10.000
Differential Impedance (?)
100
Contact - Rated Current (a)
0.5
Hot Pluggable
No
Operating Voltage Reference
AC
Operating Voltage (vac)
250
Tail Length (mm [in])
2.5 [0.098]
Header Type
Fully Shrouded
Number Of Positions
54
Number Of Signal Positions
36
Number Of Rows
9
Number Of Columns
6
Pcb Mount Retention Type
Compliant Posts
Centerline (mm [in])
1.91 [0.075]
Row-to-row Spacing (mm [in])
1.40 [0.055]
Mating Retention
Without
Contact Type
Pin
Contact Design
Rectangular Post
Contact Base Material
Phosphor Bronze
Contact Plating, Mating Area, Material
Gold
Contact Plating, Mating Area, Thickness (µm [?in])
0.76 [29.92]
Tail Plating Material
Matte Tin
Tail Plating, Thickness (µm [?in])
0.5 [20]
Connector Style
Plug
End Wall Location
Dual
Housing Color
Black
Mating Alignment
With
Mating Alignment Type
Guide Slot
Housing Material
Liquid Crystal Polymer (LCP)
Ul Flammability Rating
UL 94V-0
Number Of Pairs Per Connector
18
Pairs Per Column
3
Differential Signaling
With
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Not relevant for lead free process
Rohs/elv Compliance History
Always was RoHS compliant
Agency/standard
UL
Ul Rating
Recognized
Ul Voltage Rating (vac)
250
Operating Temperature (°c [°f])
-65 – +90 [-85 – +194]
Board-to-board Configuration
Right Angle
Pcb Thickness, Recommended (mm [in])
1.57 [0.062]
Contact Transmits (typical Application)
Signal (Data)
Packaging Method
Tube
4.
4.1.
4.2.
4.3.
4.4.
Rev B
QUALITY ASSURANCE PROVISIONS
Qualification Testing
A.
B.
Requalification Testing
If changes significantly affecting form , fit or function are m ade to the product or m anufacturing process,
product assurance shall coordinate requalification testing, consisting of all or part of the original testing
sequence as determ ined by developm ent/product, quality and reliability engineering.
Acceptance
Acceptance is based on verification that the product m eets the requirem ents of Figure 1. Failures
attributed to equipm ent, test setup or operator deficiencies shall not disqualify the product. If product
failure occurs, corrective action shall be taken and specim ens resubm itted for qualification. Testing to
confirm corrective action is required before resubm ittal.
Quality Conform ance Inspection
The applicable quality inspection plan shall specify the sam pling acceptable quality level to be used.
Dim ensional and functional requirem ents shall be in accordance with the applicable product drawing
and this specification.
Specim en Selection
Specim ens shall be prepared in accordance with applicable Instruction Sheets and shall be
selected at random from current production. Each test group shall consist of a m inim um of 3
specim ens.
Test Sequence
Qualification inspection shall be verified by testing specim ens as specified in Figure 2.
108-2303
6 of 8