5555163-5 TE Connectivity, 5555163-5 Datasheet - Page 3

• Manufacturer Part Number: 5555163-5
• Manufacturer: TE Connectivity

Specifications of 5555163-5

• Product Type: Connector
• Jack Type: RJ11
• Pcb Mounting Orientation: Side Entry (Right Angle)
• Pcb Mount Style: Through Hole
• Termination Method To Pc Board: Solder
• Performance Category: Cat 3
• Number Of Contacts Loaded: 2
• Grounding Options: Without
• Panel Stops: With
• Keyed: No
• Profile: Low
• Color: Black
• Latch Style: Standard
• Jack Configuration: 1 x 1
• Panel Mount Retention: With
• Flanged: No
• Shielded: No
• Solder Tail Contact Plating: Tin over Nickel
• Height (mm [in]): 12.70 [0.500]
• Port Configuration: Single
• Number Of Positions: 6
• Inverted Jack Face: No
• Led: Without
• Pcb Tail Length (mm [in]): 3.80 [0.150]
• Preloaded: Yes
• Contact Plating, Mating Area, Material: Gold (50)
• Contact Base Material: Phosphor Bronze
• Housing Material: PBT - GF
• Ul Flammability Rating: UL 94V-0
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
• Rohs/elv Compliance History: Always was RoHS compliant
• Pcb Thickness, Recommended (mm [in]): 1.57 [0.062]
• Packaging Method: Tray

3.4.
3.5.
Examination of product.
Termination resistance, dry circuit.
Termination resistance, rated
current.
Insulation resistance.
Dielectric withstanding voltage.
Temperature rise vs current.
Current cycling.
Shielding effectiveness, thru-hole
jacks only.
Rev G
Performance and Test Description
Product shall be designed to meet the electrical, mechanical and environmental performance
requirements specified in Figure 1.
Test Requirements and Procedures Summary
Test Description
Meets requirements of product
drawing and Application
Specifications 114-2048, 114-6016,
114-6040 and 114-6053.
∆R of 30 milliohms.
∆R of 30 milliohms.
500 megohms minimum.
One minute hold.
30° C maximum temperatur e rise at
1.5 amperes.
No evidence of physical damage.
Frequency: 30 to 400 MHz.
Reduction: 20 dB minimum.
Figure 1 (continued)
ELECTRICAL
Requirement
EIA-364-18.
Visual, dimensional and functional
per applicable inspection plan.
EIA-364-23.
Subject mated plug and jack to 50
millivolts open circuit at 100
milliamperes maximum.
See Figure 3.
EIA-364-6.
Measure potential drop of mated
plug and jack while carrying 1.5
amperes current.
See Figure 3.
EIA-364-21.
Test between adjacent contacts of
mated plug and jack.
EIA-364-20, Condition I.
1000 volts AC (rms) 60 Hz.
Test between adjacent contacts of
mated plug and jack.
EIA-364-70, Method 1.
Subject mated plug and jack to
temperature rise at rated current.
TE Spec 109-51, Condition B,
Method 2.
Subject mated plug and jack to 500
cycles at 125% of rated current for
15 minutes ON and 15 minutes
OFF.
TE Spec 109-90.
Measure radiated response from
unshielded mated jack and plug
terminated with unshielded cable
while conductors are excited
between 30 and 400 MHz. Repeat
procedure using shielded jack
mated with shielded plug terminated
with aluminum/MYLAR shielded
cable. The difference in response is
shielding effectiveness in dB.
Procedure
108-1163
3 of 7