2007464-3 TE Connectivity, 2007464-3 Datasheet - Page 3

• Manufacturer Part Number: 2007464-3
• Manufacturer: TE Connectivity

Specifications of 2007464-3

• Product Type: Cage
• Termination Type: Press-Fit
• Configuration: Single Port
• Pcb Mount: Double Sided (Belly-to-Belly)
• Termination Post Length (mm [in]): 2.05 [0.081]
• Cage Type: Single
• Cage Material: Nickel Silver
• Emi Containment: External Springs
• Lightpipe: Without
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Not relevant for lead free process
• Rohs/elv Compliance History: Always was RoHS compliant
• Application: SFP+
• Heat Sink Application: Networking
• Packaging Method: Tray

Transceiver insertion force, SFP+
m odule to PCB connector and
SFP+ cage.
Transceiver extraction force, SFP+
m odule from PCB connector and
SFP+ cage.
Cage latch strength.
Cage press fit insertion force.
Cage press fit extraction force.
Rotational cable pull.
Cable retention force.
Cable side load force.
Cable longitudinal force.
Rev C
Test Description
33.4 N [7.5 lbf] m inim um .
34 N [7.64 lbf] m axim um without
heat sink and clip.
45.37 N [10.2 lbf] m axim um with
heat sink and clip.
See Note.
12.5 N [2.8 lbf] m axim um without
heat sink and clip.
14.36 N [3.23 lbf] m axim um with
heat sink and clip.
See Note.
91.2 N [20.5 lbf] m inim um .
See Note.
44.5 N [10 lbf] m axim um for single
port cage.
54.3 N [12.2 lbf] m axim um for
ganged cage.
See Note.
8.9 N [2.0 lbf] m inim um for single
port cage.
8.9 N [2.0 lbf] m inim um for ganged
cage.
See Note.
See Note.
No discontinuities of 1 m icrosecond
or longer duration.
Shall rem ain m ated.
See Note.
No discontinuities of 1 m icrosecond
or longer duration.
Shall rem ain m ated.
See Note.
No discontinuities of 1 m icrosecond
or longer duration.
Shall rem ain m ated.
See Note.
Figure 1 (continued)
Requirem ent
EIA-364-13.
Measure force necessary to insert
m odule into connector and cage at
a m axim um rate of 12.7 m m [.5 in]
per m inute.
EIA-364-13.
Measure force necessary to extract
m odule from connector and cage at
a m axim um rate of 12.7 m m [.5 in]
per m inute.
EIA 364-98.
Apply specified axial load to latch at
a m axim um rate of 12.7m m [.5 in]
per m inute and hold for 1 m inute to
verify cage latch strength.
EIA-364-5.
Measure force necessary to push
the cage into the host board at a
m axim um rate of 12.7 m m [.5 in]
per m inute.
EIA-364-5.
Measure force necessary to push
the cage out of the host board by
applying specified force in a vertical
direction at a m axim um rate of 12.7
m m [.5 in] per m inute.
Load cable m odule into a cage
assem bly m ounted to a test board,
with attached bezel. Apply axial load
at a m axim um rate of 12.7 m m [.5
in] per m inute, rotate cable 40
degrees toward printed circuit
board, and then rotate 360 degrees
with the load still applied.
EIA-364-98.
Apply a force of 80 N [18 lbf] in an
axial direction and hold for 10
m inutes.
EIA-364-38.
Apply a force of 80 N [18 lbf] to the
cable plug in a plane parallel to the
bezel and hold for 10 m inutes.
EIA-364-38.
Apply a force of 100 N [22.5 lbf] to
the cable plug in a plane
perpendicular to the bezel and hold
for 10 m inutes.
Procedure
108-2364
3 of 6