LM311NG ON Semiconductor, LM311NG Datasheet - Page 2

• Manufacturer Part Number: LM311NG
• Description: IC COMPARATOR SGL HI VOLT 8DIP
• Manufacturer: ON Semiconductor
• Type: General Purposer

Specifications of LM311NG

• Number Of Elements: 1
• Output Type: DTL, MOS, Open-Collector, Open-Emitter, RTL, TTL
• Voltage - Supply: 5 V ~ 30 V, ±2.5 V ~ 15 V
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• Number Of Channels: 1 Channel
• Response Time: 200 ns
• Offset Voltage (max): 7.5 mV
• Input Bias Current (max): 100 nA
• Supply Voltage (max): 36 V
• Supply Voltage (min): 5 V
• Supply Current (max): 2.4 mA
• Maximum Power Dissipation: 625 mW
• Maximum Operating Temperature: + 70 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: 0 C
• Amplifier Type: Comparator
• Current, Input Bias: 45 nA
• Current, Input Offset: 1.7 nA
• Current, Supply: -5 to +7.5 mA
• Number Of Amplifiers: Single
• Package Type: PDIP-8
• Power Dissipation: 625 mW
• Temperature, Operating, Range: 0 to +70 °C
• Voltage, Gain: 200 V/mV
• Voltage, Input: ±15 VDC
• Voltage, Input Offset: 2 mV
• Voltage, Supply: 5 to 30 V
• Number Of Elements: 1
• Technology: Bipolar
• Input Offset Voltage: 7.5@±15VmV
• Input Bias Current (typ): 250nA
• Single Supply Voltage (typ): 9/12/15/18/24/28V
• Dual Supply Voltage (typ): ±3/±5/±9/±12V
• Power Supply Requirement: Single/Dual
• Voltage Gain In Db: 106.02dB
• Single Supply Voltage (min): 5V
• Single Supply Voltage (max): 30V
• Dual Supply Voltage (min): ±2.5V
• Dual Supply Voltage (max): ±15V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Through Hole
• Pin Count: 8
• Comparator Type: General Purpose
• No. Of Comparators: 1
• Ic Output Type: DTL, MOS, RTL, TTL
• Supply Current: 2.4mA
• Supply Voltage Range: 5V To 30V
• Amplifier Case Style: DIP
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: LM311NGOS

MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
* T low
NOTES: 1. Offset voltage, offset current and bias current specifications apply for a supply voltage range from a single 5.0 V supply up to 15 V supplies.
Total Supply Voltage
Output to Negative Supply Voltage
Ground to Negative Supply Voltage
Input Differential Voltage
Input Voltage (Note 2)
Voltage at Strobe Pin
Power Dissipation and Thermal Characteristics
Operating Ambient Temperature Range
Operating Junction Temperature
Storage Temperature Range
Input Offset Voltage (Note 3)
Input Offset Current (Note 3) T A = +25 C
Input Bias Current T A = +25 C
Voltage Gain
Response Time (Note 4)
Saturation Voltage
Strobe ”On” Current (Note 5)
Output Leakage Current
Input Voltage Range (T low
Positive Supply Current
Negative Supply Current
2
Plastic DIP
R S
R S
T low
T low
V CC
V ID
V ID
V ID
Derate Above T A = +25 C
V ID
V ID –10 mV, I O = 50 mA, T A = 25 C
V ID
V ID
= –25 C for LM211
= 0 C for LM311
2. This rating applies for 15 V supplies. The positive input voltage limit is 30 V above the negative supply. The negative input voltage limit is equal to the
3. The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with a 1.0 mA load. Thus,
4. The response time specified is for a 100 mV input step with 5.0 mV overdrive.
5. Do not short the strobe pin to ground; it should be current driven at 3.0 mA to 5.0 mA.
50 k , T A = +25 C
50 k , T low
5.0 mV, V O = 35 V, T A = 25 C, I strobe = 3.0 mA
10 mV, V O = 35 V, T A = 25 C, I strobe = 3.0 mA
5.0 mV, V O = 35 V, T low
6
6
negative supply voltage or 30 V below the positive supply, whichever is less.
these parameters define an error band and take into account the ”worst case” effects of voltage gain and input impedance.
T A
T A
4.5 V, V EE = 0, T low
–5.0 mV, I O = 50 mA, T A = 25 C
6.0 mV, I sink
10 mV, I sink
T high *
T high *
Rating
Ch
Characteristic
T A
(T A = +25 C, unless otherwise noted.)
8.0 mA
8.0 mA
T high *
T A
i i
T A
T high *)
T A
T high *
T high *
(V CC = +15 V, V EE = –15 V, T A = 25 C, unless otherwise noted [Note 1].)
V CC + V EE
V O –V EE
Symbol
T J(max)
1/ JA
V EE
T stg
T high = +85 C for LM211
V ID
V in
P D
T A
–
LM311 LM211
S
Symbol
= +70 C for LM311
V ICR
V OL
V IO
I CC
I EE
I IO
A V
I IB
I S
b l
V CC to V CC –5
–65 to +150
–25 to +85
LM211
+150
–14.5
36
50
30
Min
30
15
40
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
625
–14.7 to
5.0
LM211
0.75
0.23
13.8
+2.4
–1.3
Typ
200
200
0.7
1.7
3.0
0.2
0.1
45
–
–
–
–
–
–
V CC to V CC –5
–65 to +150
0 to +70
LM311
+150
36
40
30
30
15
+13.0
MOTOROLA ANALOG IC DEVICE DATA
Max
+6.0
–5.0
100
150
3.0
4.0
1.5
0.4
0.5
10
20
10
–
–
–
–
–
–
–14.5
mW/ C
Min
40
Unit
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
mW
C
C
C
–14.7 to
LM311
+2.4
0.75
0.23
13.8
–1.3
Typ
200
200
2.0
1.7
3.0
0.2
45
–
–
–
–
–
–
–
+13.0
Max
+7.5
–5.0
250
300
7.5
1.5
0.4
10
50
70
50
–
–
–
–
–
–
–
V/mV
U i
Unit
mV
mA
mA
mA
nA
nA
nA
nA
ns
V
V
A