STM8L151C8 STMicroelectronics, STM8L151C8 Datasheet - Page 87
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
STM8L151C8
Manufacturer Part Number
STM8L151C8
Description
STM8L-Ultra Low Power-8 bits Microcontrollers
Manufacturer
STMicroelectronics
Datasheet
1.STM8L151R6.pdf
(126 pages)
Specifications of STM8L151C8
Operating Power Supply
1.65 to 3.6 V (without BOR), 1.8 to 3.6 V (with BOR)
Temp. Range
−40 to 85, 105 or 125 °C
5 Low Power Modes
Wait, Low power run (5.9 μA), Low power wait (3 μA), Active-halt with full RTC (1.4 μA), Halt (400 nA)
Dynamic Power Consumption
200 μA/MHz+330 μA
Ultra Low Leakage Per I/0
50 nA
Max Freq
16 MHz, 16 CISC MIPS peak
Lcd
8x40 or 4x44 w/ step-up converter
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
STM8L151C8T3
Manufacturer:
STMicroelectronics
Quantity:
10 000
Company:
Part Number:
STM8L151C8T3TR
Manufacturer:
STMicroelectronics
Quantity:
10 000
Company:
Part Number:
STM8L151C8T6
Manufacturer:
OKI
Quantity:
1 100
Company:
Part Number:
STM8L151C8T6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
STM8L151C8T6
Manufacturer:
ST
Quantity:
20 000
STM8L15xx8, STM8L15xR6
Table 30.
1. Guaranteed by design, not tested in production.
2. Data based on characterization results, not tested in production.
Table 31.
1. C=
2. The oscillator selection can be optimized in terms of supply current using a high quality resonator with small R
3. Guaranteed by design. Not tested in production.
4. t
t
SU(HSE)
Symbol
I
DD(HSE)
C
Refer to crystal manufacturer for more details
value is measured for a standard crystal resonator and it can vary significantly with the crystal manufacturer.
f
SU(HSE)
C
f
I
HSE
R
(1)(2)
g
LSE_ext
V
LEAK_LSE
Symbol
V
m
in(LSE)
C
F
LSEH
LSEL
L1
(4)
=
C
(2)
(2)
is the startup time measured from the moment it is enabled (by software) to a stabilized 16 MHz oscillation. This
L2
(1)
(1)
High speed external oscillator
frequency
Feedback resistor
Recommended load capacitance
HSE oscillator power consumption
Oscillator transconductance
Startup time
is approximately equivalent to 2 x crystal C
LSE external clock (LSEBYP=1 in CLK_ECKCR)
The LSE is available on STM8L151xx and STM8L152xx devices only.
Subject to general operating conditions for V
LSE external clock characteristics
HSE crystal/ceramic resonator oscillator
The HSE clock can be supplied with a 1 to 16 MHz crystal/ceramic resonator oscillator. All
the information given in this paragraph is based on characterization results with specified
typical external components. In the application, the resonator and the load capacitors have
to be placed as close as possible to the oscillator pins in order to minimize output distortion
and startup stabilization time. Refer to the crystal resonator manufacturer for more details
(frequency, package, accuracy...).
HSE oscillator characteristics
External clock source frequency
OSC32_IN input pin high level voltage
OSC32_IN input pin low level voltage
OSC32_IN input capacitance
OSC32_IN input leakage current
Parameter
Parameter
Doc ID 17943 Rev 4
V
LOAD
f
f
OSC
OSC
DD
Conditions
C = 20 pF,
C = 10 pF,
.
is stabilized
= 16 MHz
=16 MHz
DD
and T
0.7 x V
Min.
V
3.5
Min.
SS
A
1
.
(3)
DD
Typ.
200
32.768
20
1
Typ.
0.6
0.46 (stabilized)
0.7 (stabilized)
Electrical parameters
2.5 (startup)
2.5 (startup)
0.3 x V
Max.
Max.
V
±1
16
DD
DD
m
value.
(3)
(3)
Unit
kHz
pF
µA
87/126
mA/V
V
MHz
Unit
mA
k
ms
pF